[ previous ] [ next ] [ threads ]
 
 From:  "Kevin R. Porter" <krp2 at bellsouth dot net>
 To:  <m0n0wall at lists dot m0n0 dot ch>
 Subject:  Beta 1.2b5 WEB GUI "Status: Wireless" page doesn't "see" Atheros /b/g wireless module, but the wireless module DOES work!
 Date:  Fri, 25 Feb 2005 18:38:37 -0500
I am successfully using an Atheros 3054MP mini-pci module (from 
www.netgate.com)  on a Soekris NET4801 box.

My wireless laptop connects to the M0n0wall just fine and is able to route 
through the M0n0wall to the Internet just fine at 802.11g (54mbit) speeds 
with 128-bit WEP enabled et al.   (WPA support would be nice addition 
though.)

However, the M0n0wall Web GUI "Status: wireless" page doesn't seem to "see" 
any wireless interface... I suspect the script is only looking for "wi0" and 
not "ath0".perhaps?

    Status: Wireless

            No supported wireless interfaces were found for status display.


Soekris console log in case its useful:
-------------------------------------------
comBIOS ver. 1.24  20040312  Copyright (C) 2000-2004 Soekris Engineering.

net4801

0128 Mbyte Memory                        CPU Geode 266 Mhz

Pri Mas  SanDisk SDCFJ-128               LBA 980-8-32  125 Mbyte

PXE-M00: BootManage UNDI, PXE-2.0 (build 082)

Slot   Vend Dev  ClassRev Cmd  Stat CL LT HT  Base1    Base2   Int
-------------------------------------------------------------------
0:00:0 1078 0001 06000000 0107 0280 00 00 00 00000000 00000000 00
0:06:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0000000 10
0:07:0 100B 0020 02000000 0107 0290 00 3F 00 0000E201 A0001000 10
0:08:0 100B 0020 02000000 0107 0290 00 3F 00 0000E301 A0002000 10
0:10:0 13A3 0020 0B400000 0116 0280 08 3C 00 A0003000 A0004000 11
0:14:0 168C 0013 02000001 0116 0290 08 3C 00 A0010000 00000000 05
0:18:2 100B 0502 01018001 0005 0280 00 00 00 00000000 00000000 00
0:19:0 0E11 A0F8 0C031008 0117 0280 08 38 00 A0020000 00000000 09

 1 Seconds to automatic boot.   Press Ctrl-P for entering Monitor.
Console: internal video/keyboard
BIOS drive C: is disk0
BIOS 639kB/130048kB available memory

FreeBSD/i386 bootstrap loader, Revision 1.1
(root at daemon5 dot neon1 dot net, Tue Feb 22 10:13:47 CET 2005)
/kernel text=0x2962ec data=0x2d44c+0x21ed8 syms=[0x4+0x3b5d0+0x4+0x4ad1a]
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.3-RELEASE #0: Tue Feb 22 17:39:26 CET 2005
    root at daemon5 dot neon1 dot net:/m0n0wall/kernels/net48xx
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (266.65-MHz 586-class 
CPU)
  Origin = "Geode by NSC"  Id = 0x540  Stepping = 0
  Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory  = 134217728 (128 MB)
avail memory = 109273088 (104 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xe100-0xe1ff mem 
0xa0000000-0xa0000fff irq 10 at d
evice 6.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: ??:??:??:??:??:??
sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0xe200-0xe2ff mem 
0xa0001000-0xa0001fff irq 10 at d
evice 7.0 on pci0
sis1: Silicon Revision: DP83816A
miibus1: <MII bus> on sis1
ukphy1: <Generic IEEE 802.3u media interface> on miibus1
ukphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: ??:??:??:??:??:??
sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0xe300-0xe3ff mem 
0xa0002000-0xa0002fff irq 10 at d
evice 8.0 on pci0
sis2: Silicon Revision: DP83816A
miibus2: <MII bus> on sis2
ukphy2: <Generic IEEE 802.3u media interface> on miibus2
ukphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: Ethernet address: ??:??:??:??:??:??
hifn0 mem 0xa0008000-0xa000ffff,0xa0004000-0xa0005fff,0xa0003000-0xa0003fff 
irq 11 at device 10.
0 on pci0
hifn0: Hifn 7955, rev 0, 32KB dram, 64 sessions
ath0: <Atheros 5212> mem 0xa0010000-0xa001ffff irq 5 at device 14.0 on pci0
ath0: mac 5.6 phy 4.1 5ghz radio 1.7 2ghz radio 2.3
ath0: Ethernet address: ??:??:??:??:??:??
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 
36Mbps 48Mbps 54Mbp
s
Geode GPIO@ = 6100
Soekris Engineering NET4801 platform
isab0: <PCI-ISA bridge> port 0x6200-0x623f,0x6100-0x613f at device 18.0 on 
pci0
isa0: <ISA bus> on isab0
pci0: <bridge, PCI-unknown> at device 18.1 (no driver attached)
atapci0: <National Geode SC1100 ATA33 controller> port 
0xe000-0xe00f,0x376,0x170-0x177,0x3f6,0x1
f0-0x1f7 at device 18.2 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
Geode CBA@ 0x6000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge, PCI-unknown> at device 18.5 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xa0020000-0xa0020fff irq 9 at 
device 19.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
cpu0 on motherboard
orm0: <ISA Option ROM> at iomem 0xc8000-0xd1fff on isa0
pmtimer0 on isa0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
Timecounters tick every 1.000 msec
Fast IPsec: Initialized Security Association Processing.
IP Filter: v3.4.35 initialized.  Default = block all, Logging = enabled
md0: Preloaded image </mfsroot> 16777216 bytes at 0xc076c918
ad0: 122MB <SanDisk SDCFJ-128/HDX 2.15> [980/8/32] at ata0-master PIO4
Mounting root from ufs:/dev/md0
Found configuration on ad0.
Initializing timezone... done
Configuring firewall... done
Configuring LAN interface... done
Configuring WAN interface... done
Configuring OPT1 (WAP) interface... done
Starting syslog service... done
Starting webGUI... done
Starting DNS forwarder... done
Starting DHCP service... done
Starting NTP client... done


*** This is m0n0wall, version 1.2b5
    built on Tue Feb 22 19:33:20 CET 2005 for net48xx
    Copyright (C) 2002-2005 by Manuel Kasper. All rights reserved.
    Visit http://m0n0.ch/wall for updates.


    LAN IP address: ???.???.???.???

    Port configuration:

    LAN   -> sis0
    WAN   -> sis2
    OPT1  -> ath0 (WAP)


m0n0wall console setup
**********************
1) Interfaces: assign network ports
2) Set up LAN IP address
3) Reset webGUI password
4) Reset to factory defaults
5) Reboot system
6) Ping host

Enter a number: