|
||||||||
Hi, I have time to time hang problem on wlan card XI626(Zcomax) in Monowall pb19r536 - generic pc. By BIOS this is detected as ID 3873, vendor 1260. HW rev: 2.0 , FW rev: 1.3.6. . PCI ports in my box uses differents IRQs. BSD detection:. /kernel: xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xcc00-0xcc7f mem 0xefdfff80-0xefdfffff irq 10 at device 3.0 on pci1 /kernel: wi0: Intersil Firmware: Primary 1.00.07, Station 1.03.06 /kernel: wi0: using RF:PRISM2.5 MAC:ISL3874A(Mini-PCI) /kernel: wi0: 802.11 address: 00:60:b3:6b:95:62 /kernel: wi0: <Intersil Prism2.5> mem 0xe7bff000-0xe7bfffff irq 11 at device 2.0 on pci1 /kernel: pci1: <PCI bus> on pcib1 /kernel: pcib1: <Intel 82801AA (ICH) Hub to PCI bridge> at device 30.0 on pci0 Reported card is in managed mode, but other, in hostap, have similar bug. Response on ping from box is OK usually, but the RX/TX part hangs. Dec 5 02:20:19/kernel: wi0: wi_cmd: busy bit won't clear. Dec 5 02:19:19/kernel: wi0: wi_cmd: busy bit won't clear. Dec 5 02:18:14/kernel: wi0: mgmt. buffer allocation failed Dec 5 02:18:14/kernel: wi0: failed to allocate 1594 bytes on NIC Dec 5 02:18:14/kernel: wi0: wi_cmd: busy bit won't clear. Dec 5 02:18:14/kernel: wi0: tx buffer allocation failed Dec 5 02:18:14/kernel: wi0: failed to allocate 1594 bytes on NIC Dec 5 02:18:14/kernel: wi0: wi_cmd: busy bit won't clear. Dec 5 02:18:14/kernel: wi0: wi_cmd: busy bit won't clear. Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc80/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc24/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc23/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc28/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc85/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc01/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc2a/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc0e/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc03/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc02/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc04/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc2d/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc0c/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc09/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc06/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc84/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc83/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc81/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc00/0; last status 800b Dec 5 02:18:14/kernel: wi0: timeout in wi_seek to fc07/0; last status 800b Dec 5 02:18:14/kernel: wi0: init failed Dec 5 02:18:14last message repeated 3 times Dec 5 02:18:14/kernel: wi0: wi_cmd: busy bit won't clear. Dec 5 02:18:14/kernel: wi0: watchdog timeout Dec 5 02:17:09/kernel: wi0: xmit failed Dec 5 02:17:09/kernel: wi0: timeout in wi_cmd 0x010b; event status 0x8000 Dec 5 01:45:12syslogd: exiting on signal 15 Marten and Scott writed hear, that the best FW for SENAO cards is 1.1.1/1.5.6. . Is possible use the same FW for XI626? Or know anybody the best FW for this card in Monowall? Thanks Michal |