|
||||||||||
Maarten, I tested this with 4 differents card. It's only a bios config on the ide port. I already installed Mono on 4 differents type of device (3 with CF) the issue was reproduced on 3 of them :) For the hardware, Epia powa :d Raphaël Maunier Maarten Poell wrote: >@ Matt > >I'm look forward to your email, which Nexcom you are using (NSA-XXXX) > >@raphael & Matt > >Yip I read somewhere that this behavior is depending on your Compact >Flash card, on a ide device you can set de jumpers for master/slave. >Some CF cards are by default in a slave setting. > >What CFcards are the both of you using? > >I also took a look at the products of Advantech, the FWA series. > >A good starter for people how are looking for hardware is to google for: >compact flash motherboards Network Security Appliance > >On Apr 6, 2005 8:12 AM, Raphael Maunier <raphael at maunier dot net> wrote: > > >>I really suggest you to test with my Bios settings. As I said, I got the >>same issue, and now this mono is up and running (on the cf card not HD >>anymore) >> >>Raphaël Maunier >> >>Matt Juszczak wrote: >> >> >> >>>We still haven't been able to get the nexcom working with the CF. >>>When we put a hard drive in, it worked fine. Although someone >>>recently did a post to the list (I forget who it was) about a fix for >>>this. We'll try it this week, and I'll let everyone know if it fixes >>>our issues. >>> >>>On Tue, 5 Apr 2005, Maarten Poell wrote: >>> >>> >>> >>>>No in our company we are thinking about buying 1 of them as a firewall >>>>for our webservices. >>>> >>>>And of course I will sent it directly to you for testing ;-) >>>> >>>>Has anybody some reallife experience with Nexcom products? >>>> >>>> >>>>On Apr 5, 2005 12:26 AM, C. Falconer <cfalconer at avonside dot school dot nz> >>>>wrote: >>>> >>>> >>>> >>>>>Do you have the units already? >>>>> >>>>>If so, you won't damage them by booting m0n0wall. The parts should >>>>>work >>>>>fine based on the freeBSD hardware list, but it does depend on whether >>>>>nexcom have done anything naughty. >>>>> >>>>>Tell you what - send me two and I'll test them for you :) >>>>> >>>>> >>>>>-----Original Message----- >>>>>From: Maarten Poell [mailto:maarten dot poell at gmail dot com] >>>>>Sent: Tuesday, 5 April 2005 10:03 a.m. >>>>>To: m0n0wall at lists dot m0n0 dot ch >>>>>Subject: [m0n0wall] Hardware Nexcom NSA 1030I-1, will it run? >>>>> >>>>>I would like to run m0n0wall on a Nexcom NSA 1030 (Via C3 1GHz, 3x >>>>>Intel >>>>>82559, Sandisk 128mb Compact Flash module). >>>>> >>>>>I checked the FreeBSD/i386 Hardware Notes and based on that it >>>>>should be >>>>>able to run on this hardware. >>>>> >>>>>But after reading the post's from Matt Juszczak (who's having >>>>>problem's with >>>>>booting from a Nexcom Nexgate 1045) I'm not sure anymore. >>>>> >>>>>Can anybody tell my if the above hardware config will work with >>>>>m0n0wall >>>>>1.11? Or can anybody give some other embedded hardware solution's >>>>>which are >>>>>proven to run with m0n0wall exept of course for the already proven >>>>>net45xx/net48xx and WRAP solutions? >>>>> >>>>>Any hints, >>>>> >>>>>Maarten >>>>> >>>>>--------------------------------------------------------------------- >>>>>To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch >>>>>For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch >>>>> >>>>> >>>>> >>>>> >>>>--------------------------------------------------------------------- >>>>To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch >>>>For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch >>>> >>>> >>>>!DSPAM:425245c0609051023666354! >>>> >>>> >>>> >>>--------------------------------------------------------------------- >>>To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch >>>For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch >>> >>> >>> >> >> |