[ previous ] [ next ] [ threads ]
 
 From:  "Barry Mather" <barry dot mather at dore dot com dot au>
 To:  "m0n0wall" <m0n0wall at lists dot m0n0 dot ch>
 Subject:  RE: [m0n0wall] PDS 2300
 Date:  Tue, 25 Oct 2005 09:12:13 +1000
Tim

Its because the usual m0n0 images don't have the nic drivers in them ...

I have it working no probs on a number of intrusion boxes, there is
instructions in the archives of this list somewhere ... Just gotta dig
them out ..

-----Original Message-----
From: Thibodeau, Dale [mailto:dthibode at uwc dot edu] 
Sent: Tuesday, 25 October 2005 6:51 AM
To: m0n0wall
Subject: RE: [m0n0wall] PDS 2300

Tim, it worked fine for me.  I bought a nokia box from ebay, booted from
a cf card (using a cd-ide adapter from newegg.com).
http://www.newegg.com/Product/Product.asp?Item=N82E16822998002

My box bombed once I turned on https authentication on the captive
portal, so right now I'm using a different box.  I guess the cpu just
couldn't handle it.

Here's instructions that apply to that unit in no particular order;
http://joeyyoung.com/html/m0n0wall-install.htm

http://chrisbuechler.com/m0n0wall/nokia/ip110.html

dale 

-----Original Message-----
From: Tim Dickson [mailto:tdickson at cordevalle dot com]
Sent: Monday, October 24, 2005 3:36 PM
To: m0n0wall at lists dot m0n0 dot ch
Subject: [m0n0wall] PDS 2300

I have an intrusion PDS 2300 and wanted to run m0n0wall on it.  In this
mailing list it looks like there have been several attempts but only one
vague success.   I decided to give it a crack.  I was unsuccessful
running from a CF card but I did however get it to boot on a m0n0wall
derived distribution called pfsense (pfsense.com - uses packet filter
instead and is running on freebsd 5.0). I did this by running it from
the hard drive instead of the CF card.  I have it fully working with LAN
WAN and OPT1 ports... it's great!  But it's very unstable, it will lock
up every minute or so.  (granted pfsense is in beta)  Has anyone been
successful with m0n0wall yet!?!?

 

Further explanations:

CF boot issues and HD success... I believe this is definitely a bios
issue.  Steps to correct this would most definitely work.

After booting from HD the ports are as follows:

            E1 = OPT1 port - disabled by default

            E2 = LAN

            E3 = WAN

I installed to HD by running the liveCD and installing from a laptop.  I
then inserted the HD into the PDS and let it boot.  I plugged in my
xover cable and upon boot I was given an IP address.  I logged into the
IP address and setup the firewall.  Every minute or so I will loose
connection though.

The website that has info on these boards is here:
http://www.ipd-us.com/productsparrow.htm 

 

That's about the extent of it...  has anyone tried the IDE to CF adapter
and seen if it can boot from that card?

I hope this helps out everyone!!!

-Tim

 

 

Tim Dickson
IT/AV Manager
One CordeValle Club Drive
San Martin, CA 95046
 
phone: 408.695.4596
fax: 408.695.4578
 
Auberge du Soleil, Napa Valley, CA
Cordevalle, San Martin, CA
Esperanza Resort, Los Cabos, Mexico
Calistoga Ranch, Napa Valley, CA
The Inn at Palmetto Bluff, Bluffton, SC 
 
www.cordevalle.com <http://www.aubergeresorts.com> 

 

 

 


---------------------------------------------------------------------
To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch