[ previous ] [ next ] [ threads ]
 From:  "David Cook" <david dot cook at jetpress dot com>
 To:  <m0n0wall at lists dot m0n0 dot ch>
 Subject:  net4801+lan1621, additional NICs undetected
 Date:  Wed, 16 Nov 2005 17:43:10 -0000
Thought I would consult the list before getting an RMA from Cortex
Systems in Denmark. We have a new Soekris net4801 with the lan1621
board. We already have another of these at a customer running m0n0wall
v1.2 and routing between 2 site to site WAN connections and the

There seems to be a problem with the unit we have here. Both m0n0wall
v1.2 and v1.1 will not detect the extra two interfaces on the lan1621
card. The relevant line from the boot log for the lan1621 card is:

pci0: <unknown card> (vendor=0xa400, dev=0xa7f0) at 10.0 irq 33

I have had a look through the PDF manual and there doesn't seem anything
to configure in the BIOS. The net4801+lan1621 at the customer site just
worked out of the box. 

Has anyone else seen this sort of behaviour with the net4801+lan1621?

Best regards.

David Cook


comBIOS ver. 1.28  20050529  Copyright (C) 2000-2005 Soekris


0128 Mbyte Memory                        CPU Geode 266 Mhz

Pri Mas  TOSHIBA THNCF128MDG             LBA 978-8-32  125 Mbyte

Slot   Vend Dev  ClassRev Cmd  Stat CL LT HT  Base1    Base2   Int
0:00:0 1078 0001 06000000 0107 0280 00 00 00 00000000 00000000
0:06:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0000000 10
0:07:0 100B 0020 02000000 0107 0290 00 3F 00 0000E201 A0001000 10
0:08:0 100B 0020 02000000 0107 0290 00 3F 00 0000E301 A0002000 10
0:10:0 A400 A7F0 00000000 0000 8210 08 3F 00 00000000 00000000
0:18:2 100B 0502 01018001 0005 0280 00 00 00 00000000 00000000
0:19:0 0E11 A0F8 0C031008 0117 0280 08 38 00 F3DE0000 00000000 05

 1 Seconds to automatic boot.   Press Ctrl-P for entering Monitor.
Console: internal video/keyboard
BIOS drive C: is disk0
BIOS 639kB/130048kB available memory

FreeBSD/i386 bootstrap loader, Revision 0.8
(root at fb411 dot neon1 dot net, Sun May  8 12:15:29 CEST 2005)
/kernel text=0x192780 data=0x209ec+0x1b778
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights
FreeBSD 4.11-RELEASE-p11 #0: Wed Sep  7 13:52:33 CEST 2005
    root at fb411 dot neon1 dot net:/usr/src/sys/compile/M0N0WALL_NET48XX
Timecounter "i8254"  frequency 1193182 Hz
CPU: NSC Geode (266.64-MHz 586-class CPU)
  Origin = "Geode by NSC"  Id = 0x540  Stepping = 0  DIR=0x81b7
real memory  = 134217728 (131072K bytes)
avail memory = 115945472 (113228K bytes)
Preloaded elf kernel "kernel" at 0xc0e2c000.
Preloaded mfs_root "/mfsroot" at 0xc0e2c0a8.
md0: Preloaded image </mfsroot> 11534336 bytes at 0xc032aacc
md1: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
sis0: <NatSemi DP83815 10/100BaseTX> port 0xe100-0xe1ff mem
f irq 10 at device 6.0 on pci0
sis0: Ethernet address: 00:00:24:c5:03:74
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: <NatSemi DP83815 10/100BaseTX> port 0xe200-0xe2ff mem
f irq 10 at device 7.0 on pci0
sis1: Ethernet address: 00:00:24:c5:03:75
miibus1: <MII bus> on sis1
ukphy1: <Generic IEEE 802.3u media interface> on miibus1
ukphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: <NatSemi DP83815 10/100BaseTX> port 0xe300-0xe3ff mem
f irq 10 at device 8.0 on pci0
sis2: Ethernet address: 00:00:24:c5:03:76
miibus2: <MII bus> on sis2
ukphy2: <Generic IEEE 802.3u media interface> on miibus2
ukphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <unknown card> (vendor=0xa400, dev=0xa7f0) at 10.0 irq 33
isab0: <PCI to ISA bridge (vendor=100b device=0510)> port
x613f at device 18.0 on pci0
isa0: <ISA bus> on isab0
chip1: <PCI to Other bridge (vendor=100b device=0511)> port
0x6300-0x63ff at dev
ice 18.1 on pci0
atapci0: <Generic PCI ATA controller> port 0xe000-0xe00f at device 18.2
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
chip2: <PCI to Other bridge (vendor=100b device=0515)> port
0x6500-0x653f at dev
ice 18.5 on pci0
ohci0: <OHCI (generic) USB controller> mem 0xf3de0000-0xf3de0fff irq 5
at device
 19.0 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
orm0: <Option ROM> at iomem 0xc8000-0xd0fff on isa0
pmtimer0 on isa0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
BRIDGE 020214 loaded
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.35 initialized.  Default = block all, Logging = enabled
ad0: 122MB <TOSHIBA THNCF128MDG> [978/8/32] at ata0-master PIO4
Mounting root from ufs:/dev/md0c
Found configuration on ad0.
Initializing timezone... done
Configuring firewall... done
Configuring LAN interface... done
Configuring WAN interface... done
Configuring OPT1 (OPT1) interface... done
Starting syslog service... done
Starting webGUI... done
Starting DNS forwarder... done
Starting DHCP service... done
Starting NTP client... done

*** This is m0n0wall, version 1.2
    built on Sun Oct  9 18:58:16 CEST 2005 for net48xx
    Copyright (C) 2002-2005 by Manuel Kasper. All rights reserved.
    Visit http://m0n0.ch/wall for updates.

    LAN IP address:

    Port configuration:

    LAN   -> sis0
    WAN   -> sis1
    OPT1  -> sis2 (OPT1)

m0n0wall console setup
1) Interfaces: assign network ports
2) Set up LAN IP address
3) Reset webGUI password
4) Reset to factory defaults
5) Reboot system
6) Ping host

Enter a number:

JP Computer Services
Nunn Close

Web:   www.jpcompserv.co.uk
Tel:   0845 083 3070
Fax:   0845 083 3071

Confidentiality Notice
This message and its contents are confidential. The contents are solely for the attention of the
recipient(s) named above and any unauthorised disclosure, copying or distribution is forbidden.  If
you are not the recipient named above, please contact the sender immediately and destroy this
message.  The views expressed in this message are those of the sender and not necessarily those of
JP Computer Services.