[ previous ] [ next ] [ threads ]
 
 From:  "Jonathan De Graeve" <Jonathan dot De dot Graeve at imelda dot be>
 To:  "Roy Daikawa" <rdaikawa at daikawa dot com>
 Cc:  "m0n0wall" <m0n0wall at lists dot m0n0 dot ch>
 Subject:  RE: [m0n0wall] DL360 Setup Issue
 Date:  Mon, 5 Dec 2005 09:30:50 +0100
I don't use hard disks :D

The G4 series have a nice internal usb-port where you just have to plug
a usb memory stick in it...

That's the easiest and most cost effective way...

J.

-- 
Jonathan De Graeve
Network/System Administrator
Imelda vzw
Informatica Dienst
015/50.52.98
jonathan dot de dot graeve at imelda dot be

---------
Always read the manual for the correct way to do things because the
number of incorrect ways to do things is almost infinite
---------

-----Oorspronkelijk bericht-----
Van: Roy Daikawa [mailto:rdaikawa at daikawa dot com] 
Verzonden: zondag 4 december 2005 23:55
Aan: Jonathan De Graeve
Onderwerp: RE: [m0n0wall] DL360 Setup Issue

Is the DL320 you are using an ATA or SCSI? If it is a SCSI Hot plug how
did
you install the software onto the hard disks or are you running it off
the
CD Rom? Just curious I have disabled all of the hardware with the
exception
of the CD and it still does not work. I have also tried it on all models
G1,
G2, G3, and a G4. Thanks for the information.

Roy Daikawa
Chief Engineer
Empower Information Systems Inc. 
732 Thimble Shoals Blvd.
Suite 103
Newport News Va. 23606
Phone: (757) 873-9771
Cell:     (757) 715-2608
Email: rdaikawa at empoweris dot com

-----Original Message-----
From: Jonathan De Graeve [mailto:Jonathan dot De dot Graeve at imelda dot be]
Sent: Sunday, December 04, 2005 10:10 AM
To: Roy Daikawa; Monowall (E-mail)
Subject: RE: [m0n0wall] DL360 Setup Issue

Which generation?

I have m0n0wall running on DL320g4 without a problem

Did you already tried a bios upgrade or disabling some hw components?

Kind Regards,

J.

--
Jonathan De Graeve
Network/System Administrator
Imelda vzw
Informatica Dienst
015/50.52.98
Jonathan dot de dot graeve at imelda dot be

> -----Oorspronkelijk bericht-----
> Van: Roy Daikawa [mailto:rdaikawa at daikawa dot com]
> Verzonden: zondag 4 december 2005 16:04
> Aan: Monowall (E-mail)
> Onderwerp: [m0n0wall] DL360 Setup Issue
>
> Tried it by Smart Starting for UNIX, Linux, and Other to no avail it
still
> hangs at the same spot.
>
> FDC0
>
> At this point I am pretty sure it is a problem with the way Monowall
> performs hardware discovery. I loaded Smooth Wall advanced server just
to
> be
> sure it would work the regular Smooth Wall would not work because it
only
> works with IDE devices and would not see the SCSI raid device. It
worked
> fine. I wish I could get this to work it would make my Monowall
redundant
> with dual power. Any help on this would be greatly appreciated.
>
>
>
> Roy Daikawa
> Chief Engineer
> Empower Information Systems Inc.
> 732 Thimble Shoals Blvd.
> Suite 103
> Newport News Va. 23606
> Phone: (757) 873-9771
> Cell:     (757) 715-2608
> Email: rdaikawa at empoweris dot com
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
> For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
>
>