|
||||||||||
Not a clue why that is, i've just looked at my cpu graph and it seems to do the same, very odd indeed. Anyone out there got any insights? Dan On 14/01/06, Gilad <gilad at bezeqint dot net> wrote: > Hi Dan, > > I checked again - it's working, and working great! > > I probably did some mistake in my previous try. > Sorry about that... > > Any way, now that the m0n0 have to do the nat, I can > see in the cpu graph that he working much harder. > > seems like every 45-50 seconds there is jump - > the cpu utilization goes up to 95-80 percent, > and immediately going back down to 8-5 percent. > > Any ideas? > > > Thanks again, > Gilad > > ----- Original Message ----- > > From: "Dan Bond" <dan dot bond at gmail dot com> > To: "Batnun" <batnun at gmail dot com> > Sent: Saturday, January 14, 2006 1:01 AM > Subject: Re: [m0n0wall] Route Modified Image updated to 1.2.1 (for anyone > using a Dlink 300T or X-modem) > > > That's the expected behaviour. Basically means that the gateway > traffic is going out over is your wan interface. Normally you get an > address there but because the ip address and gateway given by the adsl > modem are the same, you've got to tell it you want traffic going out > over your wan interface. Is it not working then? > > Dan > On 13/01/06, Batnun <batnun at gmail dot com> wrote: > > Forgot to attach the file... > > > > Gilad > > > > ----- Original Message ----- > > From: "Dan Bond" <dan dot bond at gmail dot com> > > To: "Batnun" <batnun at gmail dot com> > > Cc: "Chris Bagnall" <m0n0wall at minotaur dot cc> > > Sent: Friday, January 13, 2006 2:50 PM > > Subject: Re: [m0n0wall] Route Modified Image updated to 1.2.1 (for anyone > > using a Dlink 300T or X-modem) > > > > > > And, just cos I didn't feel like doing any work, here's the wrap > > image. Shout if it doesn't work, can't see why it would be an issue > > but hey. > > > > Dan > > > > Chris, will also send you the soekris images if that's ok, just so > > there's a whole set. Not done the CDRom cos am guessing would be > > different to the others as to how i would work with them. > > > ----- Original Message ----- > > > From: "Dan Bond" <dan dot bond at gmail dot com> > > > To: "monowall" <m0n0wall at lists dot m0n0 dot ch> > > > Sent: Friday, January 13, 2006 9:27 AM > > > Subject: Re: [m0n0wall] Route Modified Image updated to 1.2.1 (for > > > anyone > > > using a Dlink 300T or X-modem) > > > > > > > > > Will try and get around to doing this, if you've got a freebsd box you > > > can follow the instructions on http://jief.theroux.ca/?page_id=6 you > > > can follow the instructions there because it's a very simple process > > > and hopefully you should just need to replace /sbin/dhclient-script > > > with the attached one (use diff to check the only difference is the 3 > > > lines). Am going to be moving to soekris soon so will start doing > > > images for that, but if i get my act together will do all the images > > > for each release. > > > > > > Dan > > > On 13/01/06, Batnun <batnun at gmail dot com> wrote: > > > > Hi, > > > > > > > > Is there any way to convert this image to be compatible with WRAP > > > > boards? > > > > > > > > > > > > Thanks, > > > > Gilad > > > > > > > > ----- Original Message ----- > > > > From: "Chris Bagnall" <m0n0wall at minotaur dot cc> > > > > To: <m0n0wall at lists dot m0n0 dot ch> > > > > Sent: Friday, January 13, 2006 1:30 AM > > > > Subject: [m0n0wall] Route Modified Image updated to 1.2.1 (for anyone > > > > using > > > > a Dlink 300T or X-modem) > > > > > > > > > > > > > Dan has kindly updated the route-modified m0n0wall image to 1.2.1. > > > > > It > > > > > can > > > > > be > > > > > found at: > > > > > > > > > > http://www.minotaur.it/m0n0wall/routemod-generic-pc-1.2.1.img > > > > > > > > > > The older 1.2 image is still available for folks who want it. > > > > > > > > > > Regards, > > > > > > > > > > Chris > > > > > -- > > > > > C.M. Bagnall, Director, Minotaur I.T. Limited > > > > > This email is made from 100% recycled electrons > > > > > > > > > > > > > > > > > > > > --------------------------------------------------------------------- > > > > > To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch > > > > > For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch > > > > > > > > > > > > > > > > > --------------------------------------------------------------------- > > > > To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch > > > > For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch > > > > > > > > > > > > > > --------------------------------------------------------------------- > > > To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch > > > For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch > > > > > > > > > > > > > > > |