[ previous ] [ next ] [ threads ]
 
 From:  "Tech Terapies" <tech at terapies dot org>
 To:  "'Larry Gadea'" <trivex at gmail dot com>
 Cc:  <m0n0wall at lists dot m0n0 dot ch>
 Subject:  RE: [m0n0wall] PPTP 720 error
 Date:  Sun, 14 May 2006 00:50:55 +0200
Very strange problem. But I found a similar error on novell over nt 3.51
years ago.

Best regards

-----Original Message-----
From: Larry Gadea [mailto:trivex at gmail dot com]
Sent: Saturday, May 13, 2006 8:26 PM
To: tech at terapies dot org
Subject: Re: [m0n0wall] PPTP 720 error

Hi again. I managed to fix this problem. It was a lot more complicated than
I hoped it would be. It turns out I had some really bad TCP/IP settings.

Following the instructions on the following page fixed my problem:
http://www.tek-tips.com/viewthread.cfm?qid=1225579

Thanks for the help!

-- Larry Gadea.

On 5/13/06, Tech Terapies <tech at terapies dot org> wrote:
> You router accepts pass the pptp ?
> Are you put on the router the fw ip as virtual server for all traffic
> ? Or declared PAT on a cisco ?
> On the logs appears nay message ? For the pptp rule or on the system log ?
>
> -----Original Message-----
> From: Larry Gadea [mailto:trivex at gmail dot com]
> Sent: Saturday, May 13, 2006 6:05 PM
> To: tech at terapies dot org
> Subject: Re: [m0n0wall] PPTP 720 error
>
> Unfortunately, none of these worked. Disabling 128-bit encryption was
> more of a debugging thing I did. The PPTP rule already existed. I
> tried allowing fragmented packets, but no luck with that either.
>
> Any other ideas?
>
> On 5/13/06, Tech Terapies <tech at terapies dot org> wrote:
> > Do you have a pptp rule on firewall ?
> > Try to allow fragmented packets on this
> >
> > -----Original Message-----
> > From: Larry Gadea [mailto:trivex at gmail dot com]
> > Sent: Saturday, May 13, 2006 6:46 AM
> > To: m0n0wall at lists dot m0n0 dot ch
> > Subject: [m0n0wall] PPTP 720 error
> >
> > Hi.
> >
> > I cannot seem to be able to get PPTP working.
> >
> > My current settings are the following:
> >
> > Server address: 192.168.0.13
> > Remote address range: 192.168.0.208
> > RADIUS: all off/empty
> > Require 128-bit: Off
> >
> > Firewall rule:
> >
> > Action: Pass
> > Interface: PPTP
> > Protocol: Any
> > Source Type: PPTP Clients
> > Everything else is default.
> >
> > In windows XP, i simply create a new VPN connection with the proper
> > IP. I connect with the proper username/password. It connects just
> > fine and authenticates just fine. Then I get the following error
> > after 'Registering Your Computer on the Network': "Error 720: A
> > connection to the remote computer could not be established. You
> > might need to change the network settings for this connection...".
> >
> > What could I be doing incorrectly?
> >
> > Thank you.
> >
> > -- Larry Gadea.
> >
> > --------------------------------------------------------------------
> > - To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
> > For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
> >
> >
> >
>
>
>