Thank you.  One final (I hope) question.  How do I set this up so that it 
can run "inline"?  I do not wish to use IP addresses on either sis0 or sis1, 
instead, I would like the interfaces to be IP-less and have this device act 
as an in-line filter.  Do you know if this is possible?

.vp


>From: "Jonathan De Graeve" <Jonathan dot De dot Graeve at imelda dot be>
>To: "Vadim Pushkin" <wiskbroom at hotmail dot com>, <m0n0wall at lists dot m0n0 dot ch>
>Subject: RE: [m0n0wall] Need To Create A Fractional T1 Simulator

>Setup your m0n0wall as normal, enable traffic shaper create 2 pipe rules
>with the expected bandwidth, make 2 rules where you define which pipe to
>use for which direction.
>
>J.
>
>--
>Jonathan De Graeve
>Network/System Engineer
>Imelda vzw
>Informatica Dienst
>+32 15/50.52.98
>jonathan dot de dot graeve at imelda dot be
>
>---------
>Always read the manual for the correct way to do things because the
>number of incorrect ways to do things is almost infinite
>---------
>
> > -----Oorspronkelijk bericht-----
> > Van: Vadim Pushkin [mailto:wiskbroom at hotmail dot com]
> > Verzonden: donderdag 8 juni 2006 16:14
> > Aan: Jonathan De Graeve; m0n0wall at lists dot m0n0 dot ch
> > Onderwerp: RE: [m0n0wall] Need To Create A Fractional T1 Simulator
> >
> > Hi Jonathan, or anyone who cares to help,
> >
> > I am trying to set this up on a 4521, previously stated I has a 4801.
>I've
> > downloaded 1.22 (latest) onto my CF card and it is bootable.
> >
> > Upon my initial setup (through console), do I assign both LAN and WAN
>IP
> > addresses as 0.0.0.0/8? Should I IP the LAN as something like
>192.168.1.1,
> > then using the GUI, re-IP?
> >
> > How, and where, do I setup dummynet?  (I am begining to think that it
>may
> > have been named after me.. )
> >
> > Thank you all,
> >
> > .vp
> >
> > >From: "Jonathan De Graeve" <Jonathan dot De dot Graeve at imelda dot be>
> > >To: "Vadim Pushkin" <wiskbroom at hotmail dot com>, <m0n0wall at lists dot m0n0 dot ch>
> > >Subject: RE: [m0n0wall] Need To Create A Fractional T1 Simulator
> >
> > >
> > >Dummynet can perform this for you perfectly
> > >
> > >J.
> > >
> > > > -----Oorspronkelijk bericht-----
> > > > Van: Vadim Pushkin [mailto:wiskbroom at hotmail dot com]
> > > > Verzonden: maandag 5 juni 2006 15:21
> > > > Aan: m0n0wall at lists dot m0n0 dot ch
> > > > Onderwerp: [m0n0wall] Need To Create A Fractional T1 Simulator
> > > >
> > > > Hello;
> > > >
> > > > Using a Soekris (4801) and monowall, is it possible, using
>bandwith
> > > > throttloing? to create a T1 or a fractional T1 simulator? I am
>hoping
> > >to
> > > > achieve this with a 4-50Ms latency.
> > > >
> > > > Any help would be greatly appreciated.
> > > >
> > > > .vp
> > > >