Nevermind, I ofund the exec.php command!


Thanks,

.vp


>From: "Vadim Pushkin" <wiskbroom at hotmail dot com>
>To: Jonathan dot De dot Graeve at imelda dot be, m0n0wall at lists dot m0n0 dot ch
>Subject: RE: [m0n0wall] Need To Create A Fractional T1 Simulator

>
>Thank you again Jonathan, but how, or where, do I add these rules?  Do I 
>have to install the ssh agent for m0n0?  How do I access a CLI in order to 
>perform this?
>
>Also, I do not see an option anywhere for bridging sis0 to sis1.
>
>.vp
>
>>From: "Jonathan De Graeve" <Jonathan dot De dot Graeve at imelda dot be>
>>To: "Vadim Pushkin" <wiskbroom at hotmail dot com>, <m0n0wall at lists dot m0n0 dot ch>
>>Subject: RE: [m0n0wall] Need To Create A Fractional T1 Simulator
>
>>And example config if you not want to share the bandwidth evenly
>>
>>Bridge sis0 and sis1
>>
>>Ipfw add pipe 1 ip from any to (your network)
>>Ipfw pipe 1 config bw 1024Kbit/s queue 10
>>Ipfw add pipe 2 ip from (your network) to any
>>Ipfw pipe 2 config bw 1024Kbit/s queue 10
>>
>>You can do a lot of variants on this ;)
>>
>>J.
>>
>>--
>
>>
>> > -----Oorspronkelijk bericht-----
>> > Van: Jonathan De Graeve [mailto:Jonathan dot De dot Graeve at imelda dot be]
>> > Verzonden: donderdag 8 juni 2006 17:16
>> > Aan: Vadim Pushkin; m0n0wall at lists dot m0n0 dot ch
>> > Onderwerp: RE: [m0n0wall] Need To Create A Fractional T1 Simulator
>> >
>> > IIRC (for example):
>> > Bridge sis0 and sis1,
>> >
>> > Ipfw add queue 1 from any to (destination network/24)
>> > Ipfw queue 1 config weight 5 pipe 1 mask dst-ip 0x000000ff
>> > Ipfw pipe 1 config bw 1024Kbit/s
>> >
>> > Ipfw add queue 2 from (source network/24) to any
>> > Ipfw queue 2 config weight 5 pipe 2 mask src-ip 0x000000ff
>> > Ipfw pipe 2 config bw 1024Kbit/s
>> >
>> > Somebody correct me if I'm wrong...
>> >
>> > Adapt mask and dst/src network where needed.
>> >
>> > Kind Regards,
>> >
>> > J.
>> >
>> > --
>> > Jonathan De Graeve
>
>> >
>> > > -----Oorspronkelijk bericht-----
>> > > Van: Vadim Pushkin [mailto:wiskbroom at hotmail dot com]
>> > > Verzonden: donderdag 8 juni 2006 16:47
>> > > Aan: Jonathan De Graeve; m0n0wall at lists dot m0n0 dot ch
>> > > Onderwerp: RE: [m0n0wall] Need To Create A Fractional T1 Simulator
>> > >
>> > > Thank you.  One final (I hope) question.  How do I set this up so
>>that
>> > it
>> > > can run "inline"?  I do not wish to use IP addresses on either sis0
>>or
>> > > sis1,
>> > > instead, I would like the interfaces to be IP-less and have this
>> > device
>> > > act
>> > > as an in-line filter.  Do you know if this is possible?
>> > >
>> > > .vp
>> > >
>> > >
>> > > >From: "Jonathan De Graeve" <Jonathan dot De dot Graeve at imelda dot be>
>> > > >To: "Vadim Pushkin" <wiskbroom at hotmail dot com>,
>><m0n0wall at lists dot m0n0 dot ch>
>> > > >Subject: RE: [m0n0wall] Need To Create A Fractional T1 Simulator
>> > >
>> > > >Setup your m0n0wall as normal, enable traffic shaper create 2 pipe
>> > rules
>> > > >with the expected bandwidth, make 2 rules where you define which
>>pipe
>> > to
>> > > >use for which direction.
>> > > >
>> > > >J.
>> > > >
>> > > >--
>> > > >Jonathan De Graeve
>
>> > > > > -----Oorspronkelijk bericht-----
>> > > > > Van: Vadim Pushkin [mailto:wiskbroom at hotmail dot com]
>> > > > > Verzonden: donderdag 8 juni 2006 16:14
>> > > > > Aan: Jonathan De Graeve; m0n0wall at lists dot m0n0 dot ch
>> > > > > Onderwerp: RE: [m0n0wall] Need To Create A Fractional T1
>>Simulator
>> > > > >
>> > > > > Hi Jonathan, or anyone who cares to help,
>> > > > >
>> > > > > I am trying to set this up on a 4521, previously stated I has a
>> > 4801.
>> > > >I've
>> > > > > downloaded 1.22 (latest) onto my CF card and it is bootable.
>> > > > >
>> > > > > Upon my initial setup (through console), do I assign both LAN
>>and
>> > WAN
>> > > >IP
>> > > > > addresses as 0.0.0.0/8? Should I IP the LAN as something like
>> > > >192.168.1.1,
>> > > > > then using the GUI, re-IP?
>> > > > >
>> > > > > How, and where, do I setup dummynet?  (I am begining to think
>>that
>> > it
>> > > >may
>> > > > > have been named after me.. )
>> > > > >
>> > > > > Thank you all,
>> > > > >
>> > > > > .vp
>> > > > >
>> > > > > >From: "Jonathan De Graeve" <Jonathan dot De dot Graeve at imelda dot be>
>> > > > > >To: "Vadim Pushkin" <wiskbroom at hotmail dot com>,
>> > <m0n0wall at lists dot m0n0 dot ch>
>> > > > > >Subject: RE: [m0n0wall] Need To Create A Fractional T1
>>Simulator
>> > > > >
>> > > > > >
>> > > > > >Dummynet can perform this for you perfectly
>> > > > > >
>> > > > > >J.
>> > > > > >
>> > > > > > > -----Oorspronkelijk bericht-----
>> > > > > > > Van: Vadim Pushkin [mailto:wiskbroom at hotmail dot com]
>> > > > > > > Verzonden: maandag 5 juni 2006 15:21
>> > > > > > > Aan: m0n0wall at lists dot m0n0 dot ch
>> > > > > > > Onderwerp: [m0n0wall] Need To Create A Fractional T1
>>Simulator
>> > > > > > >
>> > > > > > > Hello;
>> > > > > > >
>> > > > > > > Using a Soekris (4801) and monowall, is it possible, using
>> > > >bandwith
>> > > > > > > throttloing? to create a T1 or a fractional T1 simulator? I
>>am
>> > > >hoping
>> > > > > >to
>> > > > > > > achieve this with a 4-50Ms latency.
>> > > > > > >
>> > > > > > > Any help would be greatly appreciated.
>> > > > > > >
>> > > > > > > .vp
>