[ previous ] [ next ] [ threads ]
 
 From:  tnelson at fudnet dot info
 To:  "SDamron" <sdamron at gmail dot com>
 Cc:  m0n0wall at lists dot m0n0 dot ch
 Subject:  Re: [m0n0wall] Nokia IP380
 Date:  Mon, 10 Jul 2006 10:40:20 -0500 (CDT)
The hardware is as follows:

- PIII Coppermine - 866Mhz
- 256MB PC133 ECC RAM
- Hitachi Travelstar 10GB HD
- Four Ethernet Ports

Here is a capture of the bootup procedure. I've cleaned it up a tad for
readability's sake...

<begin>
General Software Pentium III Embedded BIOS (tm) Version 4.3
Copyright (C) 2000 General Software, Inc.
Nokia NIC Trooper BIOS Version 1.1(C) 2000 General Software, Inc.
Pentium III-4.3-6E69-2A4E6

PCI Device Table.
Bus Dev Func VendID DevID Class 	     Irq
 00  00  00   1166   0009  Host Bridge
 00  00  01   1166   0009  Host Bridge
 00  09  00   104C   AC1C  CardBus Bridge
 00  09  01   104C   AC1C  CardBus Bridge
 00  0A  00   14E4   5802  Co-Processor       11
 00  0F  00   1166   0200  ISA Bridge
 00  0F  01   1166   0211  IDE Controller
 00  0F  02   1166   0220  Serial Bus         11
 01  00  00   8086   B154  PCI-to-PCI Bridge
 02  03  00   8086   1209  Ethernet           11
 02  04  00   8086   1209  Ethernet           11
 02  05  00   8086   1209  Ethernet           11
 02  06  00   8086   1209  Ethernet           11

BIOS drive C: is disk0
BIOS 637kB/261120kB available memory

FreeBSD/i386 bootstrap loader, Revision 0.8
(root at fb411 dot neon1 dot net, Sun May  8 12:15:29 CEST 2005)
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 4.11-RELEASE-p16 #0: Sun Apr  2 09:52:18 CEST 2006
    root at fb411 dot neon1 dot net:/usr/src/sys/compile/M0N0WALL_GENERIC
Timecounter "i8254"  frequency 1193182 Hz
CPU: Intel Pentium III (866.43-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x68a  Stepping = 10
 
Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory  = 268435456 (262144K bytes)
avail memory = 244572160 (238840K bytes)
Preloaded elf kernel "kernel" at 0xc1006000.
Preloaded mfs_root "/mfsroot" at 0xc100609c.
Pentium Pro MTRR support enabled
md0: Preloaded image </mfsroot> 11534336 bytes at 0xc0504e1c
md1: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pci_cfgintr: can't route an interrupt to 0:9 INTA
pcic0: <TI PCI-1225 PCI-CardBus Bridge> at device 9.0 on pci0
pcic0: PCI Memory allocated: 0x88000000
pci_cfgintr: can't route an interrupt to 0:9 INTA
pcic0: No PCI interrupt routed, trying ISA.
pcic0: Polling mode
pcic0: TI12XX PCI Config Reg: [pwr save][FUNC pci int + CSC serial isa irq]
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pci_cfgintr: can't route an interrupt to 0:9 INTB
pcic1: <TI PCI-1225 PCI-CardBus Bridge> at device 9.1 on pci0
pcic1: PCI Memory allocated: 0x88001000
pci_cfgintr: can't route an interrupt to 0:9 INTB
pcic1: No PCI interrupt routed, trying ISA.
pcic1: Polling mode
pcic1: TI12XX PCI Config Reg: [pwr save][FUNC pci int + CSC serial isa irq]
pccard1: <PC Card 16-bit bus (classic)> on pcic1
pci0: <unknown card> (vendor=0x14e4, dev=0x5802) at 10.0 irq 11
isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 ATA33 controller> port 0xf800-0xf80f at device
15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
ohci0: <OHCI (generic) USB controller> mem 0xc0010000-0xc0010fff irq 11 at
device 15.2 on pci0
usb0: OHCI version 1.0, legacy support
<end>

When ata0 is found... things start to slow down... ata1 is found... about
20 seconds later the OHCI devices are found and then it hangs. I've let it
sit there for an hour or more... no avail.

--Tim Nelson

> What is the hardware platform?  I just went through Nokia hell with a
> IP330, maybe I can help.  By hardware platform, I mean what processor,
> memory, etc.
>
> On 7/7/06, Tim Nelson <tnelson at fudnet dot info> wrote:
>> Hello! I recently acquired a Nokia IP380 and am having some issues
>> getting it to boot. I'm a 'veteran' when it comes to m0n0wall
>> installation but this one stumps me. I know the image installation
>> process worked just fine as I am able to boot the drive in any other
>> machine with no problems. I've enabled access via the serial port and am
>> able to watch it boot. Everything seems fine until the kernel
>> initializes the ide controller(s). It slows down at the point and stops
>> abruptly after initializing some sort of UHCI device. There are no
>> options in the BIOS for a USB controller or anything similar. Is there a
>> kernel parameter I can pass upon boot to disable this device? Do I need
>> a custom kernel? Help!!!
>>
>> --Tim Nelson
>>
>>
>> ---------------------------------------------------------------------
>> To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
>> For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
>>
>>
>
>
> --
> -------------------------------
> "Nothing on earth can overcome an absolutely non-resistant person."
>