|
||||||||||
Yes! I have an IP330 as well. I hope to do some work on it this evening and will take pics for you. An update on the IP380-- As mentioned, monowall hangs during bootup and right after initializing the ATA and USB controllers. pfSense gives a boat-load of page faults right as the boot loader hands off to the kernel. I was really stumped on this for a while. Upon close inspection of the motherboard, it appears there are components missing(Two capacitors for sure) as well as some scratches. I can only assume this sort of abuse would cause random malfunction... So, it is being laid to rest. On a side note, does anyone wish to purchase this for parts? I would be willing to let it go for a reasonable price... The chassis, power, cpu, HD, front panel, everything is good on it. The chassis is scratched some and the mobo is shot... --Tim > Did you have an IP330 too? > > Would it be possible for you to take a high res photo of the CPU and > surrounds next time you have that machine open? Especially the JP2 area. > > My IP330 is a 166 MHz CPU, and I've replaced it with a 450 MHz AMD. The > CPU > is detected as a 166 MHz AMD, and I'd like to see if there are any > jumpers/wiring on the board that is different to mine. > > Can you help? > > > -----Original Message----- > From: tnelson at fudnet dot info [mailto:tnelson at fudnet dot info] > Sent: Tuesday, 11 July 2006 3:40 a.m. > To: SDamron > Cc: m0n0wall at lists dot m0n0 dot ch > Subject: Re: [m0n0wall] Nokia IP380 > > > The hardware is as follows: > > - PIII Coppermine - 866Mhz > - 256MB PC133 ECC RAM > - Hitachi Travelstar 10GB HD > - Four Ethernet Ports > > Here is a capture of the bootup procedure. I've cleaned it up a tad for > readability's sake... > > <begin> > General Software Pentium III Embedded BIOS (tm) Version 4.3 Copyright (C) > 2000 General Software, Inc. Nokia NIC Trooper BIOS Version 1.1(C) 2000 > General Software, Inc. Pentium III-4.3-6E69-2A4E6 > > PCI Device Table. > Bus Dev Func VendID DevID Class Irq > 00 00 00 1166 0009 Host Bridge > 00 00 01 1166 0009 Host Bridge > 00 09 00 104C AC1C CardBus Bridge > 00 09 01 104C AC1C CardBus Bridge > 00 0A 00 14E4 5802 Co-Processor 11 > 00 0F 00 1166 0200 ISA Bridge > 00 0F 01 1166 0211 IDE Controller > 00 0F 02 1166 0220 Serial Bus 11 > 01 00 00 8086 B154 PCI-to-PCI Bridge > 02 03 00 8086 1209 Ethernet 11 > 02 04 00 8086 1209 Ethernet 11 > 02 05 00 8086 1209 Ethernet 11 > 02 06 00 8086 1209 Ethernet 11 > > BIOS drive C: is disk0 > BIOS 637kB/261120kB available memory > > FreeBSD/i386 bootstrap loader, Revision 0.8 (root at fb411 dot neon1 dot net, Sun May > 8 12:15:29 CEST 2005) Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, > 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 4.11-RELEASE-p16 #0: Sun Apr 2 09:52:18 CEST 2006 > root at fb411 dot neon1 dot net:/usr/src/sys/compile/M0N0WALL_GENERIC > Timecounter "i8254" frequency 1193182 Hz > CPU: Intel Pentium III (866.43-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x68a Stepping = 10 > > Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV, > PAT,PSE36,PN,MMX,FXSR,SSE> > real memory = 268435456 (262144K bytes) > avail memory = 244572160 (238840K bytes) > Preloaded elf kernel "kernel" at 0xc1006000. > Preloaded mfs_root "/mfsroot" at 0xc100609c. > Pentium Pro MTRR support enabled > md0: Preloaded image </mfsroot> 11534336 bytes at 0xc0504e1c > md1: Malloc disk > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > pci_cfgintr: can't route an interrupt to 0:9 INTA > pcic0: <TI PCI-1225 PCI-CardBus Bridge> at device 9.0 on pci0 > pcic0: PCI Memory allocated: 0x88000000 > pci_cfgintr: can't route an interrupt to 0:9 INTA > pcic0: No PCI interrupt routed, trying ISA. > pcic0: Polling mode > pcic0: TI12XX PCI Config Reg: [pwr save][FUNC pci int + CSC serial isa > irq] > pccard0: <PC Card 16-bit bus (classic)> on pcic0 > pci_cfgintr: can't route an interrupt to 0:9 INTB > pcic1: <TI PCI-1225 PCI-CardBus Bridge> at device 9.1 on pci0 > pcic1: PCI Memory allocated: 0x88001000 > pci_cfgintr: can't route an interrupt to 0:9 INTB > pcic1: No PCI interrupt routed, trying ISA. > pcic1: Polling mode > pcic1: TI12XX PCI Config Reg: [pwr save][FUNC pci int + CSC serial isa > irq] > pccard1: <PC Card 16-bit bus (classic)> on pcic1 > pci0: <unknown card> (vendor=0x14e4, dev=0x5802) at 10.0 irq 11 > isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <ServerWorks ROSB4 ATA33 controller> port 0xf800-0xf80f at device > 15.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > ohci0: <OHCI (generic) USB controller> mem 0xc0010000-0xc0010fff irq 11 at > device 15.2 on pci0 > usb0: OHCI version 1.0, legacy support > <end> > > When ata0 is found... things start to slow down... ata1 is found... about > 20 > seconds later the OHCI devices are found and then it hangs. I've let it > sit > there for an hour or more... no avail. > > --Tim Nelson > >> What is the hardware platform? I just went through Nokia hell with a >> IP330, maybe I can help. By hardware platform, I mean what processor, >> memory, etc. >> >> On 7/7/06, Tim Nelson <tnelson at fudnet dot info> wrote: >>> Hello! I recently acquired a Nokia IP380 and am having some issues >>> getting it to boot. I'm a 'veteran' when it comes to m0n0wall >>> installation but this one stumps me. I know the image installation >>> process worked just fine as I am able to boot the drive in any other >>> machine with no problems. I've enabled access via the serial port and >>> am able to watch it boot. Everything seems fine until the kernel >>> initializes the ide controller(s). It slows down at the point and >>> stops abruptly after initializing some sort of UHCI device. There are >>> no options in the BIOS for a USB controller or anything similar. Is >>> there a kernel parameter I can pass upon boot to disable this device? >>> Do I need a custom kernel? Help!!! >>> >>> --Tim Nelson >>> >>> >>> --------------------------------------------------------------------- >>> To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch >>> For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch >>> >>> >> >> >> -- >> ------------------------------- >> "Nothing on earth can overcome an absolutely non-resistant person." >> > > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch > For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch > > > > |