I agree that I don't need to use native vlan. However, if you take a
close look at the vlan settings from my ifconfig -a command it seems
like the vlan settings are ok.
vlan2: flags=9843<UP,BROADCAST,RUNNING,SIMPLEX,LINK0,MULTICAST> mtu 1500
inet 192.168.110.149 netmask 0xffffff00 broadcast 192.168.110.255
ether 00:04:23:c4:3d:f2
media: Ethernet autoselect (1000baseTX <full-duplex>)
status: active
vlan: 6 parent interface: em3
If you have a look at the last line where it says 'vlan: 6 parent
interface: em3'
Seems like vlan2 is just a internal header or something? I have setup
and used vlan tagging in linux countless times, with my cisco switch.
I therefore find it strange that this does not work.
Any more ideas, anyone?
Thanks,
Morten
On 8/22/06, krt <kkrrtt at gmail dot com> wrote:
> The VLAN numbers must align.
>
> on the Cisco, you're using Vlan 201
>
> On your m0n0 install, you're using Vlan0,1 and 2.
>
> You need to use the same VLAN numbers on both sides. I suggest avoiding
> using VLAN 1 on the Cisco side, as it is the default VLAN for a Cisco
> Cat (both CATOS and IOS)
>
>
> i.e.
> switchport trunk allowed vlan 0,1,2
>
> and disable the native VLAN setting - you don't need it
> no switchport trunk native vlan
>
>
> (all that the native vlan option does is send untagged frames to that
> VLAN. Since you're not dealing with that situation, you don't need it)
>
>
>
> Morten Pedersen wrote:
> > Hi.
> >
> > I have some trouble setting up VLAN with this adapter against a Cisco
> > 3750 routerswitch. It works without VLAN. Can anyone help me, if I
> > might have some wrong settings?
> >
> > $ ifconfig -a
> > em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> > options=3<RXCSUM,TXCSUM>
> > inet 82.117.32.148 netmask 0xffffff80 broadcast 82.117.32.255
> > ether 00:14:22:09:b0:a1
> > media: Ethernet autoselect (1000baseTX <full-duplex>)
> > status: active
> > em1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
> > options=3<RXCSUM,TXCSUM>
> > ether 00:04:23:c4:3d:f0
> > media: Ethernet autoselect
> > status: no carrier
> > em2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
> > options=3<RXCSUM,TXCSUM>
> > ether 00:04:23:c4:3d:f1
> > media: Ethernet autoselect
> > status: no carrier
> > em3: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> > options=3<RXCSUM,TXCSUM>
> > inet 82.117.36.149 netmask 0xffffff80 broadcast 82.117.36.255
> > ether 00:04:23:c4:3d:f2
> > media: Ethernet autoselect (1000baseTX <full-duplex>)
> > status: active
> > em4: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
> > options=3<RXCSUM,TXCSUM>
> > ether 00:04:23:c4:3d:f3
> > media: Ethernet autoselect
> > status: no carrier
> > em5: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> > options=3<RXCSUM,TXCSUM>
> > inet 192.168.120.1 netmask 0xffffff00 broadcast 192.168.120.255
> > ether 00:14:22:09:b0:a2
> > media: Ethernet autoselect (1000baseTX <full-duplex>)
> > status: active
> > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
> > inet 127.0.0.1 netmask 0xff000000
> > vlan0: flags=9842<BROADCAST,RUNNING,SIMPLEX,LINK0,MULTICAST> mtu 1500
> > ether 00:04:23:c4:3d:f2
> > media: Ethernet autoselect (1000baseTX <full-duplex>)
> > status: active
> > vlan: 200 parent interface: em3
> > vlan1: flags=9842<BROADCAST,RUNNING,SIMPLEX,LINK0,MULTICAST> mtu 1500
> > ether 00:04:23:c4:3d:f2
> > media: Ethernet autoselect (1000baseTX <full-duplex>)
> > status: active
> > vlan: 201 parent interface: em3
> > vlan2: flags=9843<UP,BROADCAST,RUNNING,SIMPLEX,LINK0,MULTICAST> mtu 1500
> > inet 192.168.110.149 netmask 0xffffff00 broadcast 192.168.110.255
> > ether 00:04:23:c4:3d:f2
> > media: Ethernet autoselect (1000baseTX <full-duplex>)
> > status: active
> > vlan: 6 parent interface: em3
> >
> >
> >
> > And on the routerswitch:
> > mol-rs-003#sh run int gigabitEthernet1/0/13
> > Building configuration...
> >
> > Current configuration : 192 bytes
> > !
> > interface GigabitEthernet1/0/13
> > description Trunk til mol-fw-001
> > switchport trunk encapsulation dot1q
> > switchport trunk native vlan 201
> > switchport mode trunk
> > spanning-tree portfast
> > end
> >
> >
> > Thanks,
> >
> > Morten
> >
> > ---------------------------------------------------------------------
> > To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
> > For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
> >
> >
>
|
