[ previous ] [ next ] [ threads ]
 
 From:  mtnbkr <waa dash m0n0wall at revpol dot com>
 To:  Guy Boisvert <boisvert dot guy at videotron dot ca>
 Cc:  m0n0wall at lists dot m0n0 dot ch
 Subject:  Re: [m0n0wall] Desperate on VLAN Config!
 Date:  Tue, 03 Oct 2006 10:01:41 -0400
Hi Guy!

You have created the VLANS, but not the INTERFACES. :)

Once you create the VLAN(s) in the VLAN tab of the "Interfaces (assign)"
page, you must then click the "Interface Assignments" TAB on that page
and click the small "plus sign" to create the INTERFACES for each of the
the newly created VLANS.

Once you do that each new VLAN interface will appear below the WAN, LAN,
and OPT1 standard interfaces. Once they appear there, the rest will be
obvious.

Good luck. Hope this helps.

--
Bill Arlofski
Reverse Polarity
waa dash m0n0wall at revpol dot com


Guy Boisvert wrote:
> Hi all!
> 
>    I need to configure my Wrap SBC (3 ether) to interface an HP switch
> using 802.1Q.  For the last 2 days, i Googled a lot and even tried the
> mOnOwall forum archive without luck.  I've seen a couple of times an URL
> which seems to contain the information i seek:
> 
> http://wiki.m0n0.ch/wikka.php?wakka=VLAN
> 
> Problem is that i get the error:
> 
> Query failed: select * from wikka_pages where tag = 'VLAN' and latest =
> 'Y' limit 1 (Can't open file: 'wikka_pages.MYI' (errno: 145))
> 
> 
> Details:
> =====
> Version: 1.22 built on Sun Apr 2 18:57:14 CEST 2006
> Platform: wrap (3 ether)
> LAN    sis0
> WAN    sis1
> OPT    sis2
> 
> 
> http://192.168.1.1/interfaces_vlan.php
> ======================================
> I have created VLANs:
> 
> sis0     1
> sis0     2
> sis0     3
> sis0     4
> sis0     10
> 
> 
> 
> 
> 
> http://192.168.1.1/exec.php
> ===========================
> $ ifconfig -a
> sis0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>    options=40<POLLING>
>    inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
>    ether 00:0d:b9:04:b0:48
>    media: Ethernet autoselect (100baseTX <full-duplex>)
>    status: active
> sis1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>    options=40<POLLING>
>    inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
>    ether 00:0d:b9:04:b0:49
>    media: Ethernet autoselect (none)
>    status: no carrier
> sis2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
>    options=40<POLLING>
>    ether 00:0d:b9:04:b0:4a
>    media: Ethernet autoselect (100baseTX <full-duplex>)
>    status: active
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
>    inet 127.0.0.1 netmask 0xff000000
> vlan0: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>    ether 00:0d:b9:04:b0:48
>    media: Ethernet autoselect (100baseTX <full-duplex>)
>    status: active
>    vlan: 1 parent interface: sis0
> vlan1: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>    ether 00:0d:b9:04:b0:48
>    media: Ethernet autoselect (100baseTX <full-duplex>)
>    status: active
>    vlan: 2 parent interface: sis0
> vlan2: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>    ether 00:0d:b9:04:b0:48
>    media: Ethernet autoselect (100baseTX <full-duplex>)
>    status: active
>    vlan: 3 parent interface: sis0
> vlan3: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>    ether 00:0d:b9:04:b0:48
>    media: Ethernet autoselect (100baseTX <full-duplex>)
>    status: active
>    vlan: 4 parent interface: sis0
> vlan4: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>    ether 00:0d:b9:04:b0:48
>    media: Ethernet autoselect (100baseTX <full-duplex>)
>    status: active
>    vlan: 10 parent interface: sis0
> 
> 
> So basically, it's very easy to create VLANs with the WEBGUI but i don't
> know how to enter the ip address of each VLAN interface.  Of course, i
> cannot test beacause interfaces have no ip address.  There is no way to
> enter IP address in  http://192.168.1.1/interfaces_vlan.php , neither in
> http://192.168.1.1/interfaces_lan.php (in this page, i have only one
> line asking for an IP address).
> 
> So if somebody could help me, it would be VERY cool!  I'm in a situation
> where i was supposed to configure a brand new firewall (A Snapgear 560)
> for a client, but we still don't have it and as a replacement, i will
> send my test WRAP firewall.  I have to ship the WRAP by wednesday...  My
> WRAP does the job great in my lab but i never had the chance to test
> 802.1Q before.  Now i have to do it fast and i don't have any
> documentation at hand!
> 
> Well, thanks in advance for any help!
> 
> Guy Boisvert
> 
> 
> 
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
> For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
>