[ previous ] [ next ] [ threads ]
 
 From:  "Raul Sampedro" <raul dot sampedro at gmail dot com>
 To:  m0n0wall <m0n0wall at lists dot m0n0 dot ch>
 Subject:  Re: [m0n0wall] Soekris 5501
 Date:  Wed, 23 Jul 2008 14:26:03 +0200
Thank you for the information Scott,

I think 1GB CF is enough for monowall (minimum requirements are 32MB ) but I
also installed pfsense in the Soekris and pfsense shows 57% used of 2GB, so
if I want use pfsense I need 2GB at least :-(

Thank you Scott

cheers

On Wed, Jul 23, 2008 at 2:16 PM, Scott Reber <sreber at atltechgroup dot com>
wrote:

> Raul,
>
> I was using Kingston 2GB cards as well.  I found a good deal on a few
> Sandisk 1GB cards last night and they work perfectly.  I set the flash
> back to primary and the 5501s now cold boot and warm boot just fine.
>
> -Scott
>
> > -----Original Message-----
> > From: Raul Sampedro [mailto:raul dot sampedro at gmail dot com]
> > Sent: Wednesday, July 23, 2008 2:48 AM
> > To: m0n0wall
> > Subject: Re: [m0n0wall] Soekris 5501
> >
> > Hello,
> >
> > I have the same problem than Scott. I'm also have a new sokris 5501
> > with
> > monowall, I dont know what kind of CF do you have, but in my case
> > I'm using
> > a Kingston 2GB CF. Sometimes boots but normally I have to connect
> > my serial
> > cable to the soekris and type reboot, then all works fine.
> >
> > Raul
> >
> > On Wed, Jul 23, 2008 at 12:35 AM, apiasecki at midatlanticbb dot com <
> > apiasecki at midatlanticbb dot com> wrote:
> >
> > > 1) Make sure you use the embedded version for CF Cards
> > > 2) Make sure you only use Sandisk brand cards for CF.
> > >
> > > I've never ran a hard drive in a soekris, kind of defeats the
> > point of a
> > > embedded system.
> > >
> > > Adam
> > >
> > >
> > > Scott Reber wrote:
> > >
> > >> I am not able to get m0n0wall 1.3b13 to cold boot on a Soekris
> > 5501 with
> > >> combios 1.33c.  I just received two of these units today and
> > both
> > >> exhibit the same symptoms.  M0n0wall begins to boot and pauses
> > for quite
> > >> a while detecting ata0 and apparently detects no disk.  It does
> > the same
> > >> for ata1.  This causes a fatal error "The device that contains
> > the
> > >> configuration file (config.xml) could not be found. M0n0wall
> > cannot
> > >> continue booting."
> > >>
> > >> If I press a key to reboot the configuration file is found.
> > >>
> > >> Does anyone have a fix?
> > >>
> > >> ______________________________________________
> > >> Scott
> > >>
> > >>
> > >> ----------------------------------------------------------------
> > -----
> > >> To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
> > >> For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
> > >>
> > >>
> > >>
> > >>
> > >>
> > >
> > > -----------------------------------------------------------------
> > ----
> > > To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
> > > For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
> > >
> > >
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
> For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
>
>