|
||||||||||
Okay, to me that sounds quite a lot like a tri honed network. You connect m0n0wall to the internat through the WAN Connect clients to m0n0wall through the LAN interface Connect the equipment (servers and the like) through OPT1 (DMZ ?) interface. That will work with m0n0wall. Out of curiosity what were using before (if anything) to do it with 2 NICs. Regards, Frans -----Original Message----- From: Greg Sims [mailto:greg underscore sims at earthlink dot net] Sent: 27 August 2003 18:27 To: Frans J King Cc: m0n0wall at lists dot m0n0 dot ch Subject: RE: [m0n0wall] Two Lan Subnets / One with DHCP Server Let's see if I can give you a better idea of the goal here ... We'd like to have two subnets called: "equipment" and "client". The equipment subnet has all the network equipment attached. The addresses on this subnet will be statically assigned. The subnet will have no bandwidth limitations. m0n0wall needs to be part of this subnet for web access. The clients attach to the client subnet. The addresses on this subnet need to be DHCP as the client population changes from day to day. We will give everyone on the subnet the same bandwidth limitation. The equipment and client subnets will both use m0n0wall as their gateway. m0n0wall will use the WAN NIC to attach to the Internet. There will be no routing between the equipment and client subnets to keep them as separate as possible. I would like to do this with two NICs if possible but I am willing to use three NICs if this is the only way with m0n0wall. Greg -----Original Message----- From: Frans J King [mailto:kingf1 at cs dot man dot ac dot uk] Sent: Wednesday, August 27, 2003 9:44 AM To: 'Greg Sims' Cc: m0n0wall at lists dot m0n0 dot ch Subject: RE: [m0n0wall] Two Lan Subnets / One with DHCP Server Greg, I'm not quite sure then what kind of setup you are aiming for. How are you going to route packets between one subnet and the other. You could for example (with 3 NICs) have a WAN interface, a LAN interface (for the DHCP enabled subnet) and a OPT interface that you use for the statically assigned machines. HTH, Frans -----Original Message----- From: Greg Sims [mailto:greg underscore sims at earthlink dot net] Sent: 27 August 2003 17:13 To: Frans J King Cc: m0n0wall at lists dot m0n0 dot ch Subject: RE: [m0n0wall] Two Lan Subnets / One with DHCP Server Thanks Frans but I really need two separate subnets. Does this mean that it is not possible to do this with m0n0wall? Thanks again, Greg -----Original Message----- From: Frans J King [mailto:kingf1 at cs dot man dot ac dot uk] Sent: Wednesday, August 27, 2003 1:11 AM To: 'Greg Sims' Cc: m0n0wall at lists dot m0n0 dot ch Subject: RE: [m0n0wall] Two Lan Subnets / One with DHCP Server I think the easiest thing would be to have an internal lan ip range of 10.43.0.0 to 10.43.1.255 and restrict the DHCP address pool to 10.43.1.0 to 10.43.1.255. Not sure if this is what you want though. Regards, Frans -----Original Message----- From: Greg Sims [mailto:greg underscore sims at earthlink dot net] Sent: 27 August 2003 03:00 To: m0n0wall at lists dot m0n0 dot ch Subject: [m0n0wall] Two Lan Subnets / One with DHCP Server Hi There, I would like to create two subnets on the LAN Interface of m0n0wall. Let's call these 10.43.0.0/24 and 10.43.1.0/24. The ip address of m0n0wall will be 10.43.0.1. All the devices on the 10.43.0.0/24 subnet will have static IP assignments. The 10.42.1.0/24 subnet will be used by clients that will be connected for a few hours at a time. This subnet will require a DHCP Server as a result. Is this kind of a configuration possible? Thanks in advance! Greg --------------------------------------------------------------------- To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch --------------------------------------------------------------------- To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch |