|
||||||||
Someone can help me ? I don't find a solution to my problem. All your ideas are welcome. Thanks for your help. Ham -----Message d'origine----- De : Falcor [mailto:falcor at netassassin dot com] Envoyé : dimanche 4 avril 2004 0:50 À : ham Cc : m0n0wall at lists dot m0n0 dot ch Objet : Re: [m0n0wall] soekris 4801 and m0n0wall looks like your 4801 is set to boot off of a hard drive and not the CF card. You need to change that. "BIOS drive C: is disk0" ham wrote: >Hello, > >I want install M0n0wall on soekris 4801 but its not fonctionning. > >I have well created the image on my CF with the tool physdiskwrite.exe > >When I boot the 4801 I receive the message : Fatal trap 12: page fault >while in kernel mode > >Here under you can find my boot sequence. > >Thanks to all for your help. > >Ham > > > >comBIOS ver. 1.24 20040312 Copyright (C) 2000-2004 Soekris >Engineering. > >net4801 > >0128 Mbyte Memory CPU Geode 266 Mhz > >Pri Mas SanDisk SDCFB-64 LBA 490-8-32 62 Mbyte > >PXE-M00: BootManage UNDI, PXE-2.0 (build 082) > >Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int >------------------------------------------------------------------- >0:00:0 1078 0001 06000000 0107 0280 00 00 00 00000000 00000000 00 >0:06:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0000000 10 >0:07:0 100B 0020 02000000 0107 0290 00 3F 00 0000E201 A0001000 10 >0:08:0 100B 0020 02000000 0107 0290 00 3F 00 0000E301 A0002000 10 >0:18:2 100B 0502 01018001 0005 0280 00 00 00 00000000 00000000 00 >0:19:0 0E11 A0F8 0C031008 0117 0280 08 38 00 A0003000 00000000 11 > > 1 Seconds to automatic boot. Press Ctrl-P for entering Monitor. >Console: internal video/keyboard >BIOS drive C: is disk0 >BIOS 639kB/130048kB available memory > >FreeBSD/i386 bootstrap loader, Revision 0.8 (root at nb dot neon1 dot net, Mon Jul >28 20:31:49 CEST 2003) /kernel text=0x198840 data=0x23e44+0x1c7a0 >syms=[0x4+0x2a810+0x4+0x317f6] >Hit [Enter] to boot immediately, or any other key for command prompt. >Booting [kernel]... >Copyright (c) 1992-2003 The FreeBSD Project. >Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights >reserved. >FreeBSD 4.9-RELEASE-p4 #0: Sat Mar 27 18:18:22 CET 2004 > root at nb dot neon1 dot net:/usr/src/sys/compile/M0N0WALL_NET48XX >Timecounter "i8254" frequency 1193182 Hz >CPU: NSC Geode (266.60-MHz 586-class CPU) > Origin = "Geode by NSC" Id = 0x540 Stepping = 0 DIR=0x81b7 > Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX> >real memory = 134217728 (131072K bytes) >avail memory = 116944896 (114204K bytes) >Preloaded elf kernel "kernel" at 0xc0d37000. >Preloaded mfs_root "/mfsroot" at 0xc0d3709c. >md0: Preloaded image </mfsroot> 10485760 bytes at 0xc0335e34 >md1: Malloc disk >npx0: <math processor> on motherboard >npx0: INT 16 interface >pcib0: <Host to PCI bridge> on motherboard >pci0: <PCI bus> on pcib0 >sis0: <NatSemi DP83815 10/100BaseTX> port 0xe100-0xe1ff mem >0xa0000000-0xa0000ff >f irq 10 at device 6.0 on pci0 >sis0: Ethernet address: 00:00:24:c1:c8:dc >miibus0: <MII bus> on sis0 >ukphy0: <Generic IEEE 802.3u media interface> on miibus0 >ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >sis1: <NatSemi DP83815 10/100BaseTX> port 0xe200-0xe2ff mem >0xa0001000-0xa0001ff >f irq 10 at device 7.0 on pci0 >sis1: Ethernet address: 00:00:24:c1:c8:dd >miibus1: <MII bus> on sis1 >ukphy1: <Generic IEEE 802.3u media interface> on miibus1 >ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >sis2: <NatSemi DP83815 10/100BaseTX> port 0xe300-0xe3ff mem >0xa0002000-0xa0002ff >f irq 10 at device 8.0 on pci0 >sis2: Ethernet address: 00:00:24:c1:c8:de >miibus2: <MII bus> on sis2 >ukphy2: <Generic IEEE 802.3u media interface> on miibus2 >ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >isab0: <PCI to ISA bridge (vendor=100b device=0510)> port >0x6200-0x623f,0x6100-0 >x613f at device 18.0 on pci0 >isa0: <ISA bus> on isab0 >chip1: <PCI to Other bridge (vendor=100b device=0511)> port >0x6300-0x63ff at dev >ice 18.1 on pci0 >atapci0: <Generic PCI ATA controller> port 0xe000-0xe00f at device 18.2 >on pci0 >ata0: at 0x1f0 irq 14 on atapci0 >ata1: at 0x170 irq 15 on atapci0 >chip2: <PCI to Other bridge (vendor=100b device=0515)> port >0x6500-0x653f at dev >ice 18.5 on pci0 >ohci0: <OHCI (generic) USB controller> mem 0xa0003000-0xa0003fff irq 11 >at devic >e 19.0 on pci0 >usb0: OHCI version 1.0, legacy support >usb0: <OHCI (generic) USB controller> on ohci0 >usb0: USB revision 1.0 >uhub0: (0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 >uhub0: 3 ports with 3 removable, self powered >orm0: <Option ROM> at iomem 0xc8000-0xd1fff on isa0 >pmtimer0 on isa0 >sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0 >sio0: type 16550A, console >sio1 at port 0x2f8-0x2ff irq 3 on isa0 >sio1: type 16550A >BRIDGE 020214 loaded >IPsec: Initialized Security Association Processing. >IP Filter: v3.4.33 initialized. Default = block all, Logging = enabled >ad0: READ command timeout tag=0 serv=0 - resetting >ata0: resetting devices .. done >ad0: 61MB <SanDisk SDCFB-64> [490/8/32] at ata0-master WDMA2 >ad0: READ command timeout tag=0 serv=0 - resetting >ata0: resetting devices .. done >ad0: READ command timeout tag=0 serv=0 - resetting >ata0: resetting devices .. done >ad0: READ command timeout tag=0 serv=0 - resetting >ad0: trying fallback to PIO mode >ata0: resetting devices .. done > > >Fatal trap 12: page fault while in kernel mode >fault virtual address = 0x780090 >fault code = supervisor read, page not present >instruction pointer = 0x8:0xc0189287 >stack pointer = 0x10:0xc029b770 >frame pointer = 0x10:0xc029b7a8 >code segment = base 0x0, limit 0xfffff, type 0x1b > = DPL 0, pres 1, def32 1, gran 1 >processor eflags = interrupt enabled, resume, IOPL = 0 >current process = Idle >interrupt mask = bio >trap number = 12 >panic: page fault > >syncing disks... >done >Uptime: 41s >Automatic reboot in 15 seconds - press a key on the console to abort >--> Press a key on the console to reboot, >--> or switch off the system now. > > > > |