[ previous ] [ next ] [ threads ]
 From:  "Grilli, Laurent" <lgrilli at be dot tiauto dot com>
 To:  "'m0n0wall at lists dot m0n0 dot ch'" <m0n0wall at lists dot m0n0 dot ch>
 Subject:  Nokia IP 110 with m0n0wall 1.0
 Date:  Tue, 13 Apr 2004 17:33:15 +0200
Hi all,

I was surprised to see on the gallery a working m0n0wall under a Nokia IP
130, that's why  
I took back my old ip 110 that was sleeping in the corner, it's running but
i all my interface (3) got a wrong mac address ! Here's the log

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.9-RELEASE-p1 #0: Wed Jan 21 19:55:40 CET 2004
    root at nb dot neon1 dot net:/usr/src/sys/compile/M0N0WALL_GENERIC
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium (266.68-MHz 586-class CPU)
  Origin = "Geode by NSC"  Id = 0x540
real memory  = 67108864 (65536K bytes)
avail memory = 50819072 (49628K bytes)
Preloaded elf kernel "kernel" at 0xc0e0e000.
Preloaded mfs_root "/mfsroot" at 0xc0e0e09c.
md0: Preloaded image </mfsroot> 10485760 bytes at 0xc040cd90
md1: Malloc disk
Using $PIR table, 3 entries at 0xc00f4fb0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
fxp0: <Intel 82559ER Embedded 10/100 Ethernet> port 0x8000-0x803f mem
0x80100000-0x8011ffff,0x80000000-0x80000fff irq 11 at device 14.0 on pci0
fxp0: Ethernet address 4d:4d:00:00:00:00
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: <Intel 82559ER Embedded 10/100 Ethernet> port 0x8400-0x843f mem
0x80300000-0x8031ffff,0x80200000-0x80200fff irq 10 at device 15.0 on pci0
fxp1: Ethernet address 4d:4d:00:00:00:00
inphy1: <i82555 10/100 media interface> on miibus1
inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp2: <Intel 82559ER Embedded 10/100 Ethernet> port 0x8800-0x883f mem
0x80500000-0x8051ffff,0x80400000-0x80400fff irq 5 at device 16.0 on pci0
fxp2: Ethernet address ff:ff:ff:ff:ff:ff
inphy2: <i82555 10/100 media interface> on miibus2
inphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <Cyrix Cx5530 PCI-ISA bridge> at device 18.0 on pci0
isa0: <ISA bus> on isab0
chip1: <PCI to Other bridge (vendor=1078 device=0101)> mem
0x40012000-0x400120ff at device 18.1 on pci0
atapci0: <Cyrix 5530 ATA33 controller> port 0xfc00-0xfc0f at device 18.2 on
atapci0: Busmastering DMA not supported
pci0: <unknown card> (vendor=0x1078, dev=0x0103) at 18.3
orm0: <Option ROMs> at iomem 0xe8000-0xebfff,0xec000-0xeffff on isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
BRIDGE 020214 loaded
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.31 initialized.  Default = block all, Logging = enabled
ad0: 4769MB <IBM-DJSA-205> [10336/15/63] at ata0-master BIOSPIO
Mounting root from ufs:/dev/md0c
Found configuration on ad0.
Initializing timezone... done
Initializing PC cards... failed (probably no PC card controller present)
Configuring firewall... done
Configuring LAN interface... done
Configuring WAN interface... done
Configuring OPT1 (OPT1) interface... done
Starting syslog service... done
Starting webGUI... done
Starting DNS forwarder... done
Starting NTP client... done

*** This is m0n0wall, version 1.0
    built on Sun Feb 15 11:09:28 CET 2004 for generic-pc
    Copyright (C) 2002-2004 by Manuel Kasper. All rights reserved.
    Visit http://m0n0.ch/wall for updates.
    LAN IP address:
    Port configuration:
    LAN   -> fxp0
    WAN   -> fxp1
    OPT1  -> fxp2 (OPT1)

m0n0wall console setup
1) Interfaces: assign network ports
2) Set up LAN IP address
3) Reset webGUI password
4) Reset to factory defaults
5) Reboot system

Enter a number: 

You will see that 2 interfaces have a mac address 4d:4d:00:00:00:00 and the
last one have ff:ff:ff:ff:ff:ff

Any idea how they manage to run it on their platforms ? Should I use a patch
? Should I post this in the dev list ?

Thanks in advance,
Laurent Grilli
TI Automotive