|
||||||||
Get a linux dist or cd and use dd that actually works. Just a tip -----Ursprungligt meddelande----- Från: Chet Harvey [mailto:chet at pittech dot com] Skickat: den 14 april 2004 20:42 Till: Mr Paul J Ogilvie; m0n0wall at lists dot m0n0 dot ch Ämne: Rv: RE: [m0n0wall] Physdiskwrite and HD's Sure your machine is booted up, Just kidding. That is bizarre and I am at a loss to how to fix it. Anyone? --------- Mensagem Original -------- From: Mr Paul J Ogilvie <support at stmc dot bc dot ca> To: m0n0wall at lists dot m0n0 dot ch <m0n0wall at lists dot m0n0 dot ch> Subject: RE: [m0n0wall] Physdiskwrite and HD's Date: 14/04/04 19:21 > > Mine goes like this... > > > D:>physdiskwrite.exe -u generic-pc-1.0.img > physdiskwrite v0.4 by Manuel Kasper <mk at neon1 dot net> > Searching for physical drives... > > Which disk do you want to write? (0..-1) > > > So it looks like the program is not finding the drives... interesting. > > > > > -----Original Message----- > Subject: Rv: RE: RE: [m0n0wall] Physdiskwrite and HD's > Date: 14/04/04 09:08 > > ok sorry for the delay. This is what I get when I run it on my desktop here > at work: > > C:>physdiskwrite.exe -u net45xx-1.0.img > > physdiskwrite v0.4 by Manuel Kasper <mk at neon1 dot net> > > Searching for physical drives... > > Information for \.PhysicalDrive0: > Windows: cyl: 10337 > tpc: 240 > spt: 63 > C/H/S: 16383/16/63 > Model: Maxtor 6Y080L0 > Serial number: Y2582LFE > Firmware rev.: YAR41BW0 > > Which disk do you want to write? (0..0) > > > What do you see on yours? > > > --------- Mensagem Original -------- > Subject: RE: RE: [m0n0wall] Physdiskwrite and HD's > Date: 13/04/04 20:43 > > > > > That's the thing there is no list (at least that I can see)... > > Should there be a listing at the beginning when the program loads? > > > > > > > > -----Original Message----- > > From: Chet Harvey [mailto:chet at pittech dot com] > > Sent: Tuesday, April 13, 2004 11:32 AM > > To: Mr Paul J Ogilvie > > Subject: Rv: RE: [m0n0wall] Physdiskwrite and HD's > > > > hmmm....does it show your drive in the 0..1 list? > > > > meaning does it ID it properly? > > > > --------- Mensagem Original -------- > > From: Mr Paul J Ogilvie &lt;support at stmc dot bc dot ca&gt; > > To: 'Chet' &lt;chet at pittech dot com&gt; > > Subject: RE: [m0n0wall] Physdiskwrite and HD's > > Date: 13/04/04 20:01 > > > > &gt; > > &gt; Yup... I am using version 0.4 and I have included the -u option > (trying to > > &gt; use a Fujitsu 1.0GB drive) in the command. Any other ideas? > > &gt; > > &gt; > > &gt; > > &gt; > > &gt; > > &gt; -----Original Message----- > > &gt; From: Chet [mailto:chet at pittech dot com] > > &gt; Sent: Tuesday, April 13, 2004 10:02 AM > > &gt; To: Mr Paul J Ogilvie; m0n0wall at lists dot m0n0 dot ch > > &gt; Subject: Rv: [m0n0wall] Physdiskwrite and HD's > > &gt; > > &gt; Couple of questions: > > &gt; > > &gt; 1) which version are you using? > > &gt; > > &gt; If under version 0.4, go grab 0.4 > > &gt; > > &gt; 2) is the drive to install on over 800mb? > > &gt; > > &gt; if over this, use the &amp;quot;-u&amp;quot; switch. > > &gt; > > &gt; HTH > > &gt; > > &gt; --------- Mensagem Original -------- > > &gt; From: Mr Paul J Ogilvie &amp;lt;support at stmc dot bc dot ca&amp;gt; > > &gt; To: m0n0wall at lists dot m0n0 dot ch &amp;lt;m0n0wall at lists dot m0n0 dot ch&amp;gt; > > &gt; Subject: [m0n0wall] Physdiskwrite and HD's > > &gt; Date: 13/04/04 17:47 > > &gt; > > &gt; &amp;gt; Hey everyone. > > &gt; > > &gt; I have the CDROM ISO running fine on my m0n0wall box; however, I want > to > > set > > &gt; it up using a regular HD. When I go through the process of using > > &gt; Physdiskwrite, it comes to a point where it asks for &amp;quot;which > disk do > > you want > > &gt; to write? (0..-1)&amp;quot;. At this point, it does not matter what > I input - > > the > > &gt; program just repeats the question. Any ideas? > > &gt; > > &gt; > > &gt; Paul > > &gt; > > &gt; > > &gt; > > &gt; > > &gt; > > &gt; > > > > > > > > > > > > > > > > > > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch > For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch > > > > > --------------------------------------------------------------------- To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch --- Incoming mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.658 / Virus Database: 422 - Release Date: 2004-04-13 --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.658 / Virus Database: 422 - Release Date: 2004-04-13 |