sorry for OT..

I am looking for a cheaper IP telephony, one with more cost effective, to
use
with my m0n0wall boxes.
Can anyone help me?

thx
Toledo

----- Original Message ----- 
From: "Paul Rasmussen" <paura at rkl dot no>
To: <m0n0wall at lists dot m0n0 dot ch>
Sent: Tuesday, May 04, 2004 3:16 AM
Subject: Re: Re: [m0n0wall] VoIP Conf


> > >>Alex -- are you using a VoIP software phone on your computer, or do
> > >>you have an external VoIP box?
> > >>
> > >>Here are my rules which I'm using to good success with my
> > Vonage VoIP
> > >>box, which is "vox," below.  Let me know if you need to see
> > an example
> > >>of traffic shaping to increase the priority of VoIP
> > traffic, I think
> > >>I've got that sussed, as well.
> > >>
> > >>     <nat>
> > >>        <rule>
> > >>            <protocol>udp</protocol>
> > >>            <external-port>69</external-port>
> > >>            <target>vox</target>
> > >>            <local-port>69</local-port>
> > >>            <descr>VoIP</descr>
> > >>        </rule>
> > >>        <rule>
> > >>            <protocol>udp</protocol>
> > >>            <external-port>123</external-port>
> > >>            <target>vox</target>
> > >>            <local-port>123</local-port>
> > >>            <descr>VoIP</descr>
> > >>        </rule>
> > >>        <rule>
> > >>            <protocol>udp</protocol>
> > >>            <external-port>4500</external-port>
> > >>            <target>twowords</target>
> > >>            <local-port>4500</local-port>
> > >>            <descr>VPN traffic</descr>
> > >>        </rule>
> > >>        <rule>
> > >>            <protocol>udp</protocol>
> > >>            <external-port>5060-5063</external-port>
> > >>            <target>vox</target>
> > >>            <local-port>5060</local-port>
> > >>            <descr>VoIP</descr>
> > >>        </rule>
> > >>        <rule>
> > >>            <protocol>udp</protocol>
> > >>            <external-port>10000-20000</external-port>
> > >>            <target>vox</target>
> > >>            <local-port>10000</local-port>
> > >>            <descr>VoIP</descr>
> > >>        </rule>
> > >>     </nat>
> > >>
> > >>[...]
> > >>
> > >>     <filter>
> > >>        <rule>
> > >>            <interface>wan</interface>
> > >>            <protocol>udp</protocol>
> > >>            <source>
> > >>                <any/>
> > >>            </source>
> > >>            <destination>
> > >>                <address>vox</address>
> > >>                <port>5060-5063</port>
> > >>            </destination>
> > >>            <descr>NAT VoIP</descr>
> > >>        </rule>
> > >>        <rule>
> > >>            <interface>wan</interface>
> > >>            <protocol>udp</protocol>
> > >>            <source>
> > >>                <any/>
> > >>            </source>
> > >>            <destination>
> > >>                <address>vox</address>
> > >>                <port>123</port>
> > >>            </destination>
> > >>            <descr>NAT VoIP</descr>
> > >>        </rule>
> > >>        <rule>
> > >>            <interface>wan</interface>
> > >>            <protocol>udp</protocol>
> > >>            <source>
> > >>                <any/>
> > >>            </source>
> > >>            <destination>
> > >>                <address>vox</address>
> > >>                <port>69</port>
> > >>            </destination>
> > >>            <descr>NAT VoIP</descr>
> > >>        </rule>
> > >>        <rule>
> > >>            <interface>wan</interface>
> > >>            <protocol>udp</protocol>
> > >>            <source>
> > >>                <any/>
> > >>            </source>
> > >>            <destination>
> > >>                <address>vox</address>
> > >>                <port>10000-20000</port>
> > >>            </destination>
> > >>            <descr>NAT VoIP</descr>
> > >>        </rule>
> > >>     </filter>
> > >>
> > >>
> > >>Adam
> > >>
> > >>-- 
> > >>Lose your mind and come to your senses.  -Fritz Perls
> > >> <adam at baz dot org>
> > >>
> > >
> > > Hi Adam,
> > >
> > > I'm trying to run VoIP on a Sipura external box but so far
> > it hasn't
> > > been too successful. I would be greatful for an example of you VoIP
> > > traffic shapeing.
> > >
> > > Regards,
> > > Paul
> >
> > Paul,
> >
> > With my Sipura SPA-2000 phone adapter and VoicePulse VOIP service, I
> > configured m0n0wall with the following NAT settings:
> >
> > Inbound NAT
> > -----------
> > Proto: UDP
> > Ext. port range: 5060
> > NAT IP: 10.0.0.199 (change as needed)
> > Int. port range: 5060
> >
> > Proto: UDP
> > Ext. port range: 5061
> > NAT IP: 10.0.0.199 (change as needed)
> > Int. port range: 5061
> >
> > This allows incoming phone calls. Outbound phone calls worked without
> > any changes to m0n0wall's default firewall rule set.
> > Add firewall rules as needed for your setup.
> >
> > z
> >
> >
>
> The Sipura is working fine with the default settings of m0n0wall but I'll
> give this a try. The main problem is that the connection is closing and
with
> the receiving part loosing contact first. My voice fading away...
> This is the reason for using m0n0wall and trying traffic shaping for the
> first time. The problem is most likely the cable I'm connected to but I
like
> to test this before changing to adsl.
> I have gone through the ones on the list but so far I am missing
something.
> So anyone who can give me some examples of traffic shaping rules please
do.
>
> Paul
>
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
> For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
>