My static IP, the one that is seen from the internet is 200.x.x.x. My modem
s IP, the one that I use
 to access its web gui, is 172.207.1.1. My m0n0wall box's ip is 192.168.1.1.
 
As soon as my ADSL modem is in bridge (PPTP) mode, what values should I type
in:
 
STATIC ROUTES (session)
Interface: ?
Destination network: ?
Gateway: ?
 
WAN (interfaces session)
Type: Static or PPTP?
 
- If it is Static:

IP Address: ? / ?
Gateway: ?
 
- If it is PPTP:
 
Username: (That's ok. I know what my user name is)
Password: (That's ok too.)
Local IP Address: ? / ?
Remote IP address: ?
 
 
I am looking forwarding for your answer!
 
Thank you,
 
Cristian
 
 
-------Mensagem original-------
 
De: Christiaens Joachim
Data: Friday, October 03, 2003 09:34:24
Para: 'Thomas Hertz'; Assinatura de Listas
Cc: m0n0wall at lists dot m0n0 dot ch
Assunto: RE: [m0n0wall] Steps to use my ADSL modem in "brige" mode with
m0n0wall
 
If I understand it OK, then the static IP of the ADSL modem was a private
one (on the inside of the NAT), so that one we will not be using.
 
Instead, I think you would setup a pptp connection over the wan ethernet
connection...
 
Again, I haven't done this on m0n0wall before...
 
Joachim
 
-----Original Message-----
From: Thomas Hertz [mailto:thomas at hz dot se]
Sent: donderdag 2 oktober 2003 21:29
To: Assinatura de Listas
Cc: m0n0wall at lists dot m0n0 dot ch
Subject: Re: [m0n0wall] Steps to use my ADSL modem in "brige" mode with
m0n0wall
 
 
When your ADSL modem is in bridge mode, it doesn't have any IP address 
at all (with exception from the web interface IP which you will not be 
using here). So, after you've read your ADSL modem manual and set your 
modem in bridge mode, you just enter your static IP (the one your ADSL 
modem used to have) as the WAN ip on m0n0wall. Then everything should 
work as expected.
 
--
Thomas Hertz
 
 
Assinatura de Listas wrote:
 
>Thank you... but, in fact, I think it is easier to use my ADSL modem in 
>
>bridge" mode. My next question is: as soon as my ADSL modem is in brige
mode
>
>what are the next steps to configure m0n0wall? I used to type my modem's
>
>static ip in m0n0wall's static route session, but what I am going to do
now?
>
>What are the steps to configure WAN interface?? 
>
> 
>
>Thank you, 
>
> 
>
>Cristian 
>
> 
>
> 
>
>-------Mensagem original------- 
>
> 
>
>De: Aaron Robinson 
>
>Data: Thursday, October 02, 2003 19:33:53 
>
>Para: Assinatura de Listas 
>
>Cc: mk at neon1 dot net; m0n0wall at lists dot m0n0 dot ch 
>
>Assunto: Re: [m0n0wall] Steps to use m0n0wall in bridge mode 
>
> 
>
>Bruce Mah wrote a nice tutorial on it. I haven't used it, but it's at: 
>
>http://www.employees.org/~bmah/Software/m0n0wall/ 
>
> 
>
>That should get you going. 
>
> 
>
>Good luck! 
>
>Aaron 
>
> 
>
>On Thursday, October 2, 2003, at 06:59 AM, Assinatura de Listas wrote: 
>
> 
>
> 
>
>>Please Manuel Kasper, would you show me the steps to use m0n0wall in 
>> 
>>
>
> 
>
>>bridge 
>> 
>>
>
> 
>
>>mode? My GS-R250S Plus/Duo ADSL Router is also a NAT router. 
>> 
>>
>
> 
>
>
> 
>
>>I'm looking forward for you help! 
>> 
>>
>
> 
>
>
> 
>
>>Thank you, 
>> 
>>
>
> 
>
>
> 
>
>>Cristian 
>> 
>>
>
> 
>
>
> 
>
>>--------------------------------------------------------------------- 
>> 
>>
>
> 
>
>>To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch 
>> 
>>
>
> 
>
>>For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch 
>> 
>>
>
> 
>
>
> 
>
>
>. 
>
>---------------------------------------------------------------------
>To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
>For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
>
> 
>
 
 
 
---------------------------------------------------------------------
To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
 
 
-----------------------------------------------
MISSION STATEMENT 
-----------------------------------------------
Oce enables its customers to manage their documents efficiently and
effectively by offering innovative print and document management products
and services for professional environments.
 
-----------------------------------------------
DISCLAIMER 
-----------------------------------------------
This e-mail message and any attachment are intended for the sole use of the
recipient(s) named above and may contain information which is confidential
and/or protected by intellectual property rights.
Any use of the information contained herein (including, but not limited to,
total or partial reproduction, communication or distribution in any form) by
other persons than the designated recipient(s) is prohibited.
 
If you have received this e-mail in error, please notify the sender either
by telephone (0032-2-729.48.11) or by e-mail and delete the material from
any computer.
Oce-Belgium/Oce-Interservices is nor responsible for the correct and
complete transfer of the contents of the sent e-mail, neither for the
receipt on due time. This e-mail message does not bring about a contractual
obligation for Oce-Belgium/Oce-Interservices.
 
Thank you for your cooperation.
 
For further information about Oce-Belgium/Oce-Interservices please see our
website at www.oce.be
 
-----------------------------------------------
 
.