[ previous ] [ next ] [ threads ]
 
 From:  "Bryan Kohlstedt" <bk at aventuremail dot com>
 To:  m0n0wall at lists dot m0n0 dot ch, aaron at digitalvideogroup dot com
 Subject:  Re: [m0n0wall] Can connect via PPTP but cannot see any remote computers
 Date:  Fri, 9 Jul 2004 21:07:26 +0100
Is there a reason you need to use network neighborhood? The reason I ask is what I usually do is to
just use a net use command and map whatever drive I need once I'm connected. I know this isn't a
solution for every application.

I would say switch back to having your pptp clients and lan in the same ip scheme and give mapping
drives a try (if it's a valid solution for your situation).

Bryan

----- Original Message -----
From: "Aaron Tunnell" <aaron at digitalvideogroup dot com>
To: <m0n0wall at lists dot m0n0 dot ch>
Sent: Friday, July 09, 2004 11:15 AM
Subject: [m0n0wall] Can connect via PPTP but cannot see any remote computers

 Well I tried both suggestions.  I changed my VPN config to a new subnet in
 the 51 range.  And I created a LMHOSTS file on the XP client that mapped
 192.168.50.100 to the server.  But I still cant see anything on the remote
 network after I successfully connect.  Any more ideas?-Aaron
 
 Gateway Lan address 192.168.50.1
 DHCP range is 192.168.50.5-192.168.50.100
 My server VPN address is 192.168.51.101
 And my Client VPN assigned address is 192.168.51.144
 
 -----Original Message-----
 From: Zadikem, Travis-taz [mailto:tzadikem at picosecond dot com]
 Sent: Thursday, July 08, 2004 11:21 AM
 To: Aaron Tunnell; m0n0wall at lists dot m0n0 dot ch
 Subject: RE: [m0n0wall] Can connect via PPTP but cannot see any remote
 computers
 
 
 I had the same problem.  Do you have a wins server on the side that you
 can't see.  If not,
 you can just populate an LMHOSTS file on the windows XP as follows as an
 example:
 
 192.168.1.2	COMPUTERNAME	#PRE
 
 make sure you use tabs between the items.
 
 Travis
 
 
 
 
 -----Original Message-----
 From: Aaron Tunnell [mailto:aaron at digitalvideogroup dot com]
 Sent: Thursday, July 08, 2004 8:58 AM
 To: m0n0wall at lists dot m0n0 dot ch
 Subject: [m0n0wall] Can connect via PPTP but cannot see any remote
 computers
 
 
 I set up PPTP VPN according to the directions, below is my configuration on
 the Monowall box.  I can connect to my monowall from work via the built in
 WinXP client, but I cannot see any of my computers that are behind the
 monowall in network neighborhood.  Any idea why I can connect but cant see
 anything?  I set up the addresses as best I could figure, but I may have a
 conflict on my subnets.  So here is my config, any ideas?
 
 Gateway Lan address 192.168.50.1
 DHCP range is 192.168.50.5-192.168.50.100
 My server VPN address is 192.168.50.101
 And my Client VPN assigned address is 192.168.50.144
 
 The subnet at work where I am connecting form is in the 192.168.2.x range is
 this a conflict with the above?  Thanks for any help!
 
 ---------
 Aaron Tunnell
 Digital Media Specialist
 Avid ACSR Windows | Unity
 Digital Video Group, inc.
 10049 Lickinghole Rd. - Suite A
 Ashland, VA 23005
 804-752-6650
 804-752-6651 fax
 aaron at digitalvideogroup dot com
 
 
 ---------------------------------------------------------------------
 To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
 For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
 
 
 ---------------------------------------------------------------------
 To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
 For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
 
 
 ---------------------------------------------------------------------
 To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
 For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch

--------------------------

AventureHost.com - Worldwide Hosting - http://www.aventurehost.com
Sent from AventureMail.com, 2GB Free Email!