Hi everybody,
have my brandnew Soekris net4801 machine, this one has BIOS 1.34 dated
20040312, 128 MB Ram, 266 Mhz CPU. Set it to "ConSpeed=9600" now I can
both see the BIOS from the machine and the m0n0wall boot-output.
I tried with different net48xx Images: the stable 1.0 and the 1.1b16,
tried both on different CF-cards (SanDisk 64 MB and a SanDisk 512 MB,
both "normal" not "ultra" versions).
No such luck, it boots okay, but "panics" after a while (the output
below is captured via Linux' minicom).
I did create the media on a (Debian) linux machine with SanDisk USB
CF-reader SDDR-31 "dd if=<image.img> of=/dev/sda bs=16k" also omitted
the bs, changed it to 8k, etc. every try results in the "panic" :-/
fdisk shows the following (that's the 512 MB card):
Disk /dev/sda: 16 heads, 62 sectors, 1009 cylinders
Units = cylinders of 992 * 512 bytes
8 partitions:
# start end size fstype [fsize bsize cpg]
a: 1 5 5 4.2BSD 1024 8192 26
c: 1 5 5 unused 0 0
Anyone have a clue what I might try to get m0n0wall to boot
successfully?
TIA and kind regards from Aachen (Germany)
Frederick
POST: 0123456789bcefghipajklnoq,,,tvwxy
comBIOS ver. 1.24 20040312 Copyright (C) 2000-2004 Soekris Engineering.
net4801 CPU Geode 266 Mhz 0000 Mbyte Memory0128
Pri Mas SanDisk SDCFB-64 LBA 490-8-32 62 Mbyte
PXE-M00: BootManage UNDI, PXE-2.0 (build 082)
Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int
-------------------------------------------------------------------
0:00:0 1078 0001 06000000 0107 0280 00 00 00 00000000 00000000 00
0:06:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0000000 10
0:07:0 100B 0020 02000000 0107 0290 00 3F 00 0000E201 A0001000 10
0:08:0 100B 0020 02000000 0107 0290 00 3F 00 0000E301 A0002000 10
0:18:2 100B 0502 01018001 0005 0280 00 00 00 00000000 00000000 00
0:19:0 0E11 A0F8 0C031008 0117 0280 08 38 00 A0003000 00000000 11
Seconds to automatic boot. Press Ctrl-P for entering Monitor.
> show
ConSpeed = 9600
ConLock = Enabled
ConMute = Disabled
BIOSentry = Enabled
PCIROMS = Enabled
PXEBoot = Enabled
FLASH = Primary
BootDelay = 5
BootPartition = Disabled
ShowPCI = Enabled
Reset = Hard
> reboot
Console: internal video/keyboard
BIOS drive C: is disk0
BIOS 639kB/130048kB available memory
FreeBSD/i386 bootstrap loader, Revision 0.8
(root at nb dot neon1 dot net, Sat May 29 16:47:22 CEST 2004)
/kernel text=0x1a0940 data=0x20e70+0x1c774 syms=[0x4+0x2af90+0x4+0x32146/
Booting [kernel]...
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.10-RELEASE #0: Sun Jun 20 11:21:18 CEST 2004
root at nb dot neon1 dot net:/usr/src/sys/compile/M0N0WALL_NET48XX
Timecounter "i8254" frequency 1193182 Hz
CPU: NSC Geode (266.66-MHz 586-class CPU)
Origin = "Geode by NSC" Id = 0x540 Stepping = 0 DIR=0x81b7
Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory = 134217728 (131072K bytes)
avail memory = 116916224 (114176K bytes)
Preloaded elf kernel "kernel" at 0xc0d3e000.
Preloaded mfs_root "/mfsroot" at 0xc0d3e09c.
md0: Preloaded image </mfsroot> 10485760 bytes at 0xc033c004
md1: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
sis0: <NatSemi DP83815 10/100BaseTX> port 0xe100-0xe1ff mem 0xa0000000-0xa0000fff irq 10 at device
6.0 on pci0
sis0: Ethernet address: 00:00:24:c2:a3:fc
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: <NatSemi DP83815 10/100BaseTX> port 0xe200-0xe2ff mem 0xa0001000-0xa0001fff irq 10 at device
7.0 on pci0
sis1: Ethernet address: 00:00:24:c2:a3:fd
miibus1: <MII bus> on sis1
ukphy1: <Generic IEEE 802.3u media interface> on miibus1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: <NatSemi DP83815 10/100BaseTX> port 0xe300-0xe3ff mem 0xa0002000-0xa0002fff irq 10 at device
8.0 on pci0
sis2: Ethernet address: 00:00:24:c2:a3:fe
miibus2: <MII bus> on sis2
ukphy2: <Generic IEEE 802.3u media interface> on miibus2
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=100b device=0510)> port 0x6200-0x623f,0x6100-0x613f at device 18.0
on pci0
isa0: <ISA bus> on isab0
chip1: <PCI to Other bridge (vendor=100b device=0511)> port 0x6300-0x63ff at device 18.1 on pci0
atapci0: <Generic PCI ATA controller> port 0xe000-0xe00f at device 18.2 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
chip2: <PCI to Other bridge (vendor=100b device=0515)> port 0x6500-0x653f at device 18.5 on pci0
ohci0: <OHCI (generic) USB controller> mem 0xa0003000-0xa0003fff irq 11 at device 19.0 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
orm0: <Option ROM> at iomem 0xc8000-0xd1fff on isa0
pmtimer0 on isa0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
BRIDGE 020214 loaded
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.33 initialized. Default = block all, Logging = enabled
ad0: READ command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. done
ad0: 61MB <SanDisk SDCFB-64> [490/8/32] at ata0-master WDMA2
ad0: READ command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. done
ad0: READ command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. done
ad0: READ command timeout tag=0 serv=0 - resetting
ad0: trying fallback to PIO mode
ata0: resetting devices .. done
Fatal trap 12: page fault while in kernel mode
fault virtual address = 0x780090
fault code = supervisor read, page not present
instruction pointer = 0x8:0xc018a1df
stack pointer = 0x10:0xc02a3870
frame pointer = 0x10:0xc02a38a8
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = Idle
interrupt mask = bio
trap number = 12
panic: page fault
syncing disks...
done
Uptime: 41s
Automatic reboot in 15 seconds - press a key on the console to abort |
