Yeah, it found your NIC just fine.  Unfortunately, you need two NICs for
m0n0wall to work.

- Eric


----- Original Message ----- 
From: "Rainer Zocholl" <UseNet dash Posting dash Nospam dash 74308 dash  at zocki dot toppoint dot de>
To: <m0n0wall at lists dot m0n0 dot ch>
Sent: Sunday, August 08, 2004 1:11 PM
Subject: Re: [m0n0wall] NE2000 ISA Howto?


> ayocee at gmail dot com(Kirk Lane)  08.08.04 07:53
>
> >On 08 Aug 2004 15:02:00 +0200, Rainer Zocholl
> >>
> >> i'm trying to run m0n0wall under Bochs.
> >> Bochs emulates an NE2000 ISA card, non-PnP, nonPCI
> >> at port 0x300 irq 3
> >>
> >> But it seems not to be able to find that cards,
> >> tho NE2000 ist listed in HCL.
> >>
> >> I don't see any way where i can enter the
> >> network driver manually.
>
> >http://your.m0n0wall.address/exec.php
>
> Thanks. But i have NO network access at all
> i'm stuck on the setup page!
>
> Bochs is a x86-simulator which simulates only that kind
> of ethernet cards.
>
>
> >And run 'dmesg'.
> >See if you can find your cards showing up,
>
> I see the boot messages scrolling up (it's not so fast)
>
> >or related error messages.
>
> There are no error messages.
> (but i wonder how it could find a sio at irq3..)
>
>
> Booting from Hard Disk...
>
> BTX loader 1.00  BTX version is 1.01
> Console: internal video/keyboard
> BIOS drive C: is disk0
> BIOS 639kB/64512kB available memory
>
> FreeBSD/i386 bootstrap loader, Revision 0.8
> (root at nb dot neon1 dot net, Sat May 29 16:47:22 CEST 2004)
>
> /kernel text=0x2e34e0 data=0x44adc+0x231d4 syms=[0x4+0x3fd10+0x4+0x47b20]
>
> Hit [Enter] to boot immediately, or any other key for command prompt.
> {no wait occurs}
> Booting [kernel]...
>
> Copyright (c) 1992-2004 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> FreeBSD 4.10-RELEASE #0: Sun Jun 20 11:16:54 CEST 2004
>     root at nb dot neon1 dot net:/usr/src/sys/compile/M0N0WALL_GENERIC
> ...
>
> npx0: error reporting broken; using 387 emulator
> isa0: <ISA bus> on motherboard
> orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
> pmtimer0 on isa0
> fdc0: <NEC 765 or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
> ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
> ata1 at port 0x170-0x177,0x376 irq 15 on isa0
> >{there is only one ata-controler}
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model Generic PS/2 mouse, device ID 0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> >{hm, there no serial port configured..}
> sio1: configured irq 3 not in bitmap of probed irqs 0
> BRIDGE 020214 loaded
> IPsec: Initialized Security Association Processing.
> IP Filter: v3.4.33 initialized.  Default = block all, Logging = enabled
> ata0-slave: ATAPI identify retries exceeded
> ad0: 9MB <Generic 1234> [20/16/63] at ata0-master BIOSPIO
> Mounting root from ufs:/dev/md0c
> Found configuration on ad0.
> Initializing timezone... done
> Initializing PC cards... failed (probably no PC card controller present)
> Configuring firewall... done
> Configuring LAN interface... done
> Configuring WAN interface... done
> Starting syslog service... done
> Starting webGUI... done
> Starting DNS forwarder... done
> Starting NTP client... done
>
> etc..
> But no ethernet card was found!
>
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
> For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
>