[ previous ] [ next ] [ threads ]
 
 From:  "Holger Bauer" <Holger dot Bauer at citec dash ag dot de>
 To:  "Nieder, Bernd" <bernd dot nieder at gilbarco dot de>, "Chet Harvey" <chet at pittech dot com>
 Cc:  <m0n0wall at lists dot m0n0 dot ch>
 Subject:  AW: AW: [m0n0wall] LAN + Wireless interface only?
 Date:  Wed, 1 Sep 2004 15:15:42 +0200
I have tried this already and I had some strange things and also still some blocks, even if allowing

that are not seen in the webadministration (look at http://ip-of-mono/status.php to see all rules).

webadministration I guess. 



regards,
Holger Bauer



Von: Chet Harvey [mailto:chet at pittech dot com]
Gesendet: Mittwoch, 1. September 2004 14:43
An: Nieder, Bernd
Cc: m0n0wall at lists dot m0n0 dot ch
Betreff: Re: AW: [m0n0wall] LAN + Wireless interface only?


Can you simply just use the WAN designated interface on your LAN? I have done
that too. Just changed the default ruleset. That should make m0n0 happy and you too.


Chet Harvey
Pitbull Technologies <http://www.pittech.com/> 
Protecting your Digital Assets
703.407.7311


Quoting "Nieder, Bernd" <bernd dot nieder at gilbarco dot de>:

> Right. This was the intended purpose of the box. I already thought about to
> put in an unused interface but it's too tight in the case that I use.
> 
> I'm afraid that I have to buy another case to add a third interface.
> 
> Thanks,
> Bernd
> 
> 

> Von: Chet Harvey [mailto:chet at pittech dot com] 
> Gesendet: Dienstag, 31. August 2004 20:15
> An: Nieder, Bernd
> Cc: m0n0wall at lists dot m0n0 dot ch
> Betreff: Re: [m0n0wall] LAN + Wireless interface only?
> 
> WAN and LAN are required. What I have done for a teesting box is just assign
> a an unused interface to WAN and only use LAN and OPT1(wifi) for testing.
> 
> So if I read your email properly, you basically want m0n0 to sit between
> your WLAN clients and your out-bound "router" or LAN switch. Thereby you can
> shape their traffic and or apply rules and pass then thru the LAN interface
> to the lan.
> 
> Chet Harvey
> Pitbull Technologies <http://www.pittech.com/> Protecting your Digital
> Assets
> 703.407.7311
> 
> 
> Quoting "Nieder, Bernd" <bernd dot nieder at gilbarco dot de>:
> 
> >  Hi,
> > 
> > Is it possible to set up a configuration with LAN and WLAN interface only
> > (without WAN)? I'd like to use m0n0 for a special purpose as an AP with
> more
> > influence on the traffic.
> > 
> > I'm using an EPIA MII board. When I try to set up m0on0 just with the
> > onboard interface installed the configuration ends up with 'sis0' as LAN
> and
> > 'sis1' as WAN - though I assigned 'vr0' as LAN interface and nothing for
> > WAN.
> > 
> > BTW: under normal conditions (LAN+WAN interface installed) the onboard NIC
> > works pretty fine as 'vr0'.
> > 
> > Any hints?
> > 
> > Thanks,
> > Bernd 
> > 
> 

---------------------------------------------------------------------
To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch


____________
Virus checked by G DATA AntiVirusKit