Daniele,
I will setup a test m0n0 wall here and let you know but from your interface
output it almost seems like there are no IP's assigned to vlan 100-104? 

$ ifconfig vlan1
vlan1: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	ether 00:50:8b:5a:26:f6
	media: Ethernet autoselect (100baseTX <full-duplex>)
	status: active
	vlan: 102 parent interface: fxp1

$ ifconfig vlan2
vlan2: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	ether 00:50:8b:5a:26:f6
	media: Ethernet autoselect (100baseTX <full-duplex>)
	status: active
	vlan: 103 parent interface: fxp1

$ ifconfig vlan3
vlan3: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	ether 00:50:8b:5a:26:f6
	media: Ethernet autoselect (100baseTX <full-duplex>)
	status: active
	vlan: 104 parent interface: fxp1


Other then that your switch config looks fine.

Jake

-----Original Message-----
From: Daniele Guazzoni [mailto:daniele dot guazzoni at gcomm dot ch] 
Sent: Saturday, September 04, 2004 4:36 AM
To: Jake S
Subject: Re: [m0n0wall] m0n0wall VLAN (fxp and Cisco Catalyst) problem

Jake

It is a Cat 2950-24 with IOS 12.1.22 (c2950-i6q4l2-mz.121-22.EA1.bin).
Attached you'll find the command results.
I also tried to reduce the MTU to 1480 on the VLANs ( a tip I read 
somewhere on the web) which altough does not provide any help.

Attached are the result of the commands on the cat and an ifconfig on 
the m0n0wall.

Daniele

Jake S wrote:
> Can you provide the following commands?
> 
> sho run
> sho vlan
> sho int trunk  <-- not sure if this one will be available to you or not.
> 
> Also... what IOS are you running on that switch?
> 
> Thank you,
> Jake Seitz - Founder
> Agatestreet.com - Cleaning Inbox's one domain at a time!
> http://www.agatestreet.com
> d 1.866.850.1608
> f 1.858.964.6461
> 
> -----Original Message-----
> From: Daniele Guazzoni [mailto:daniele dot guazzoni at gcomm dot ch] 
> Sent: Friday, September 03, 2004 6:01 PM
> To: m0n0wall List
> Subject: [m0n0wall] m0n0wall VLAN (fxp and Cisco Catalyst) problem
> 
> I've configured my m0n0wall to use VLAN on an fxp dual 100baseTX card.
> Actually VLANs 101 to 104 are configured on fxp1.
> The fxp1 port is connected to a Cisco Catalyst 2950.
> The cat port is configured for 802.1q trunking and it sees the VLANs.
> 
> No traffic is passing from the m0n0wall to the VLANs on the Cat.
> 
> Any idea ?
> 
> 
> regards
> 
> 
> ------------------------------------------------------------------
> 
> Daniele Guazzoni
> Network & System Engineer
> Cisco Certified Network Professional
> 
> ------------------------------------------------------------------
> "Destiny is not a matter of chance, it is a matter of choice;
> it is not a thing to be waited for, it is a thing to be achieved."
>                          William Jennings Bryan
> 
> 
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
> For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch
>