[ previous ] [ next ] [ threads ]
 
 From:  "C. Falconer" <cfalconer at avonside dot school dot nz>
 To:  "'James W. McKeand'" <james at mckeand dot biz>, "'Sergey Velikanov [UzPAK]'" <vgray at uzpak dot uz>
 Cc:  m0n0wall at lists dot m0n0 dot ch
 Subject:  RE: Re[2]: [m0n0wall] No link UP
 Date:  Thu, 23 Sep 2004 09:06:08 +1200
VMware provides virtual ethernet cards based on the AMD Lance PCI ethernet
chipset, so lnc0 is quite likely the virtual VM Ware cards.



-----Original Message-----
From: James W. McKeand [mailto:james at mckeand dot biz] 
Sent: Thursday, 23 September 2004 6:31 a.m.
To: 'Sergey Velikanov [UzPAK]'
Cc: m0n0wall at lists dot m0n0 dot ch
Subject: RE: Re[2]: [m0n0wall] No link UP


Have you tried to manually assigning the NICs? Use the names given for the
NICs (i.e. lnc0 and lnc1) instead of auto-detection.

Search the list archive for vmware. I remember reading about some one using
it before. I have used Microsoft Virtual PC 2004 to simulate a m0n0wall. I
would look at how the NICs are set up. I have not use vmWare for a while, so
I cannot tell you where to look. Compare your other FreeBSD VMs with the
m0n0wall one.

_________________________________
James W. McKeand


-----Original Message-----
From: Sergey Velikanov [UzPAK] [mailto:vgray at uzpak dot uz] 
Sent: Wednesday, September 22, 2004 10:31 AM
To: James W. McKeand
Subject: Re[2]: [m0n0wall] No link UP

Hi
There are no result
http://ds.uzpak.uz/screenshot.jpg

Maybe it becouse I use vmWare, but FreeBsd 4.10 and FreeBSD 5.2.1 works fine
as virtual machine

>-----Original Message-----
>From: James W. McKeand <james at mckeand dot biz>
>To: "'Sergey Velikanov [UzPAK]'" <vgray at uzpak dot uz>,
><m0n0wall at lists dot m0n0 dot ch>
>Date: Wednesday, September 22, 2004, 6:57:10 PM
>Subject: [m0n0wall] No link UP

> I have seen this before, I think the interfaces are initially shown as
> sis#, until you run the Interface assignment. Then, the

> I have also seen the auto-detection work only when you boot with no
> interfaces connected. (This assumes that you have at least *TWO NICS* 
> in your m0n0wall box)

> 1) Boot with no cables connected to your NICs.
> 2) From console setup: hit 1 (Interfaces: assign network ports) - you
> should get a list of your NICs with MAC addresses.
> 3) Hit "n" for no VLANs.
> 4) Connect the cable to the NIC you want to be the LAN interface.
> 5) Hit "a" for auto-detection. The NIC you just connected should be 
> detected and assigned as LAN.
> 6) Connect the cable to the NIC you want to be the WAN interface.
> 7) Hit "a" for auto-detection. The NIC you just connected should be 
> detected and assigned as WAN.
> 8) If you have any OPT interfaces, repeat #6 and #7. OR press return 
> to exit the assignment
> 9) From a workstation on you LAN, connect to WebGUI at http://<LANIP> 
> ... I think you can take it from here...

> If I am wrong, someone correct me.

> Good luck & have fun.

> _________________________________
> James W. McKeand


> -----Original Message-----
> From: Sergey Velikanov [UzPAK] [mailto:vgray at uzpak dot uz]
> Sent: Wednesday, September 22, 2004 1:24 AM
> To: m0n0wall at lists dot m0n0 dot ch
> Subject: [m0n0wall] No link UP

> Hi

> I've run monowall, but it incorrect detect my network card, normally
> it detected as

> FreeBSD 5.2.1-RELEASE
> ifconfig
> lnc0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500

> but monowall detect it as sis0, and when I press "1" then "n" then "a" 
> and "Enter" in main menu monowall say that there is no link

> How can I run monowall on my network card ?

> Sergey Velikanov
> Technical  Division
> National Data Network "UzPAK"
> tel +(99871) 114-6326
> e-mail:  vgray at uzpak dot uz
> http://www.uzpak.uz/



> ---------------------------------------------------------------------
> To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
> For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch


> ---------------------------------------------------------------------
> To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
> For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch



---------------------------------------------------------------------
To unsubscribe, e-mail: m0n0wall dash unsubscribe at lists dot m0n0 dot ch
For additional commands, e-mail: m0n0wall dash help at lists dot m0n0 dot ch